Jump to content
SAU Community

Recommended Posts

hey everyone im new on this so yep its my first time on this forum. i have an issue with my skyline with the head lights cover that its very dirty and has foggy stains from the insides of the head light cover, im just wondering how do i get rid of and clean it. i tried to see if you can take of the head light cover but i think its just one big piece and you cant. so if can somebody help me thats would be excellent

Edited by twinz

assuming it is similar to the 32 headlight. And I think it should be.

You can put it in the oven (seriously). What I did when I had to open my headlight was.

- Put aluminum foil in tray/grill

- Pre-heat the oven to 180c (without the headlight in it)

- TURN OVERN OFF

- Place headlight in the tray for approximately 5 mins

- The sealant should be soft enough for you to open up the headlight using a screw driver.

Now, there is probabaly some clips holding the over on the outside, so be sure to remove those 1st before you put in the oven. Also besure to remove all the wire and globe...etc

assuming it is similar to the 32 headlight. And I think it should be.

You can put it in the oven (seriously). What I did when I had to open my headlight was.

- Put aluminum foil in tray/grill

- Pre-heat the oven to 180c (without the headlight in it)

- TURN OVERN OFF

- Place headlight in the tray for approximately 5 mins

- The sealant should be soft enough for you to open up the headlight using a screw driver.

Now, there is probabaly some clips holding the over on the outside, so be sure to remove those 1st before you put in the oven. Also besure to remove all the wire and globe...etc

whats the best way to take the headlights off without breaking the clips that hold the lights in place.....

ever heard of a search ?

well

this person is new and could be eager to know something ...too eager to do a search perhaps.....

saying "search" isnt being helpful as well...

as for the headlight

there are products to clean it. but with plastic......you will notice that there might be hairline cracks when you look at it in the light.

Edited by eeiko321

there are no cracks in the head light thats 100% so ill try the plastic cleaner for sure and give that a go and will see what happens... hopefully that will fix the foggy headlights cross fingers.

its on the outside... we do it at work all day every day

we make them come up literally as good as theyll ever get which is damn good!!!!

do not put them in the oven theyre totally different to r32 as what as has been suggested above

there are no cracks in the head light thats 100% so ill try the plastic cleaner for sure and give that a go and will see what happens... hopefully that will fix the foggy headlights cross fingers.

well ive found the plastic polish always works.... but like i said...look very very closely in broad day light. sometimes you could see very very fine cracks. and Generally dirty headlights always have them.

if by any chance it doesnt work, there was a mob in Windsor whom glazes headlights and could mould it via the plastic one you have...

because with glass you actually dont lose any % of light

its on the outside... we do it at work all day every day

we make them come up literally as good as theyll ever get which is damn good!!!!

do not put them in the oven theyre totally different to r32 as what as has been suggested above

what do you guys use to clean up the head lights. what solution...

well ive found the plastic polish always works.... but like i said...look very very closely in broad day light. sometimes you could see very very fine cracks. and Generally dirty headlights always have them.

if by any chance it doesnt work, there was a mob in Windsor whom glazes headlights and could mould it via the plastic one you have...

because with glass you actually dont lose any % of light

do you know the details of the mobb in Windsor by any chance

i use an RO polisher with paint polish to correct my headlights.

Edge green pad with Menzerna IP 3.01 does the trick.

If you have access to someone who can detail cars, just mask up around the headlight and polish it with a machine and paint polish.

get mcguires plast-x and scrub the hell out of the outsides.... you'll be surprised what this stuff can do

That's what I used on mine, came up like new in literally minutes.

I initially thought mine were dirty on the inside too, not the case however.

That's what I used on mine, came up like new in literally minutes.

I initially thought mine were dirty on the inside too, not the case however.

so all you did was just use a rag and the plastic polish and scrub the hell out of it was it...

From the latest HPI magazine (No. 106) there is an article on the exact thing you're after I believe.

I have scanned the page. Sorry if it's hard to read, it was a large image when I uploaded it but photobucket must have down-sized it.

HPI-Clean-Headlights.jpg

Hope that helped,

-Jimmy.

Edited by -Jimmy-
do you know the details of the mobb in Windsor by any chance

unfortunately i dont

this was years ago... look up glass glaziers...

some of them can actually mould a shape if you can send them the plastic headlight

give the polish a try...

i recall there was a comparison test with plastic vs glass in headlights and plastic aftermarket headlight shields sold, particularly for off road 4wds... and with plastic.. 5% of light is actually lost.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Per Mark Roberts of Sonictune: Mark Robert Author At this time, no. No ETA either 2016-17 models. You will be able to purchase and install a 2018.5+ TCU though   TCU purchasing and pricing info! As we near the release of TCU tuning, I am going to answer some questions I get asked often.   What do I need for TCU tuning? At this time, you will need a 2018.5+ TCU to be able to tune. If you have a 2016-to early 2018, you will need to replace your TCU with the newer version. One good way to know if your TCU is good is if you have auto upshift in manual mode in 1st gear around 6500 rpms. If your manual 1st gear goes to 7k rpm and will hit the rev limiter unless you shift, you have the older TCU.   Why do I need to buy another ecu license/phone flash if I already have it on my ECU tune? The TCU is its own computer module. It is completely separate from the ECU. Because of this, you will be required to purchase a TCU license and, if your tuner has it, the phone flash license required to tune it via phone/bluetooth.   Do I need TCU tuning? TCU tuning is NOT required. However, the faster your setup, the more it will assist in track and dragy time consistency.   If I’m ECU tuned by (tuner A) can I get my TCU tuned by (Tuner ? Yes, since it’s a different module and a completely separate flash, you can have two different tuners. However, it is highly recommend that you have both tuned by the same tuner. For me, my TCU tuning will directly complement my ECU tuning style and features and running my ECU and another TCU or vice versa MIGHT cause some issues. At this time and for the foreseeable future, I will only be tuning my current ECU tuned customers TCUs.     I have a SYVECS AWD controller. Do I still need it? Yes! The AWD controllers main job is to control your AWD system. However, with TCU tuning, you will no longer need the auto-shift function as that will be done through the TCU. The AWD controller will still be very beneficial for racers looking to maximize traction on the launch.     Shift schedule changes: holding gears longer at lower pedal input as well as max shift rpm changes. Please note, the new ECU race rom coming out will address 90% of the shitty drivability issues these cars have through custom maps from myself and Racebox—as well as others I am sure.   Increase shift speeds: as seen in the videos I’ve been posting, the TCU shifts much faster once tuned.   Increased shift pressures: as also seen in the videos, much firmer full throttle shifts.      
    • Per Mark Roberts of Sonictune:     Mark Robert Author At this time, no. No ETA either 2016-17 models. You will be able to purchase and install a 2018.5+ TCU though   TCU purchasing and pricing info! As we near the release of TCU tuning, I am going to answer some questions I get asked often.   What do I need for TCU tuning? At this time, you will need a 2018.5+ TCU to be able to tune. If you have a 2016-to early 2018, you will need to replace your TCU with the newer version. One good way to know if your TCU is good is if you have auto upshift in manual mode in 1st gear around 6500 rpms. If your manual 1st gear goes to 7k rpm and will hit the rev limiter unless you shift, you have the older TCU.   Why do I need to buy another ecu license/phone flash if I already have it on my ECU tune? The TCU is its own computer module. It is completely separate from the ECU. Because of this, you will be required to purchase a TCU license and, if your tuner has it, the phone flash license required to tune it via phone/bluetooth.   Do I need TCU tuning? TCU tuning is NOT required. However, the faster your setup, the more it will assist in track and dragy time consistency.   If I’m ECU tuned by (tuner A) can I get my TCU tuned by (Tuner ? Yes, since it’s a different module and a completely separate flash, you can have two different tuners. However, it is highly recommend that you have both tuned by the same tuner. For me, my TCU tuning will directly complement my ECU tuning style and features and running my ECU and another TCU or vice versa MIGHT cause some issues. At this time and for the foreseeable future, I will only be tuning my current ECU tuned customers TCUs.     I have a SYVECS AWD controller. Do I still need it? Yes! The AWD controllers main job is to control your AWD system. However, with TCU tuning, you will no longer need the auto-shift function as that will be done through the TCU. The AWD controller will still be very beneficial for racers looking to maximize traction on the launch.     Shift schedule changes: holding gears longer at lower pedal input as well as max shift rpm changes. Please note, the new ECU race rom coming out will address 90% of the shitty drivability issues these cars have through custom maps from myself and Racebox—as well as others I am sure.   Increase shift speeds: as seen in the videos I’ve been posting, the TCU shifts much faster once tuned.   Increased shift pressures: as also seen in the videos, much firmer full throttle shifts.      
    • The fancy pants red shock tower brace is finally incoming from MX5 Mania, getting it shipped from 'Merica has been a long and problematic process, and GWR, the 'Merican supplier will not ship directly to consumers outside of the US, Mania basically had to order a heap of them, the colour choice was silver, or red, and we all know anything red adds 5 killerwasps of dynotorques..... Whilst it does fit over a 2.5, and I've seen a few photos and videos of it being installed and fitting, google also says it might get real close to the FAB9 intake front runner, people in the US says it does fit with the FAB9 intake, except for one person who said it slightly touched.......so there is that.....LOL..... As it seems that I am the first in AU to have this combination of parts there's no local knowledge about fitment, so I'm just a willing guinea pig in this endeavour, I'll cross my fingers and toes and hope for the best In other news, I ordered stuff from China  on the same day I ordered the 23° silicone bend from Victoria, the stuff from China arrived a day ago, the 23° silicone bend is still travelling around Australia thanks to Australia Post, and "may" be here next week
    • Very good news...I contacted Racebox about it last night. My car is a 2016 so remains to be seen if it is compatible, requires a TCU swap, or is impossible.
    • What ECU are you running? This is probably the biggest question. If it's a PowerFC, I'd probably change the ECU and get something newer that will handle the injectors in a nicer way.
×
×
  • Create New...