Jump to content
SAU Community

Recommended Posts

Hi Gents,

I am new to the forum.

I have a R33 GTST '94 done about 112K. I gave my car for Serive yesterday and was told to change the timing belt.

Does any1 know how many k's can the above model skyline do before it becomes a must to change it?

Even though i have requested for it to be changed, I thought maybe it could be helpfull to have an understanding for me and for others in the forum

Thanks

Harry

Link to comment
https://www.sau.com.au/forums/topic/266379-r33-timing-belt/
Share on other sites

hi there,

Working in an auto parts store as well working side jobsas well as on my own vehicle's i never play the how many miles game. Rather better safe than sorry. good luck,

~skott

so your telling me your gonna change the Timing belt (without any idea or planning/scedule) every 20,000km ....replace just to be safe then sorry?

:P

Hi Gents,

I am new to the forum.

I have a R33 GTST '94 done about 112K. I gave my car for Serive yesterday and was told to change the timing belt.

Does any1 know how many k's can the above model skyline do before it becomes a must to change it?

Even though i have requested for it to be changed, I thought maybe it could be helpfull to have an understanding for me and for others in the forum

Thanks

Harry

it all depends... sometimes rubbers can last longer than others, depending on the ingredients made.

but average recommendations are usually 100,000km.

so if your car hasnt had it done before, its most likely due.

Timing chains usually last a fair bit longer

Link to comment
https://www.sau.com.au/forums/topic/266379-r33-timing-belt/#findComment-4547296
Share on other sites

I bought a s1 r33 with 127000kays on the clock and I suspected the timing belt had never been changed, so i did it + water pump just to be on the safe side.

however now i'm regretting not doing the idler/tensioner pulleys at the same time... apparently if they go it's just as bad! ??

Edited by dnbosiris
Link to comment
https://www.sau.com.au/forums/topic/266379-r33-timing-belt/#findComment-4550092
Share on other sites

if it looks cracked, or teeth missing chips replace

usually they say every 90,000 to 100,000kms

if u dont and it snaps you WILL need new pistons and valves as the 2 meet at a very fast pace

bent valves can also equal cracked valve guides, distorted valve seats, the dust from the chunks taken out of the piston may end up getting picked up in a main bearing journal

alot of machining work and labour hours/costs involved

unless u get lucky and the bent valves do minimal damage, but still $30 + per valve isnt cheap at 24

Edited by Gerg_R31
Link to comment
https://www.sau.com.au/forums/topic/266379-r33-timing-belt/#findComment-4550113
Share on other sites

I bought a s1 r33 with 127000kays on the clock and I suspected the timing belt had never been changed, so i did it + water pump just to be on the safe side.

however now i'm regretting not doing the idler/tensioner pulleys at the same time... apparently if they go it's just as bad! ??

yes i forgot to mention about that one

it is also recommended to replace the idle tensioner puller with the timing belt.. because they are also very old.

well it depends...sometimes its not as bad.....it causes anoyying rattles and squeeks

Link to comment
https://www.sau.com.au/forums/topic/266379-r33-timing-belt/#findComment-4550222
Share on other sites

anyone know what the factory timing settings are for the RB25? am changing my timing belt and having troubles

ok RB25DET timing is as follows:

15 degrees +/- 1 Degrees, 650 +/- 50rpm

ive got a simplified Workshop manual of the R33 Rb25det aroudn 20mgb which shows you how to test it if you need

cheers

Link to comment
https://www.sau.com.au/forums/topic/266379-r33-timing-belt/#findComment-4566372
Share on other sites

so your telling me your gonna change the Timing belt (without any idea or planning/scedule) every 20,000km ....replace just to be safe then sorry?

:woot:

:) should have clarified. i usually do timing on my cars around 60,000 reason: i run the piss out of them. highway runs country side twistie's and if i ever get a chance tracks.

Link to comment
https://www.sau.com.au/forums/topic/266379-r33-timing-belt/#findComment-4567413
Share on other sites

:P should have clarified. i usually do timing on my cars around 60,000 reason: i run the piss out of them. highway runs country side twistie's and if i ever get a chance tracks.

country runs..... well id say definately get them replaced more often to avoid havoc....

as steve irwin said "if ya break down ere........ its ALL OVA!" :happy:

Link to comment
https://www.sau.com.au/forums/topic/266379-r33-timing-belt/#findComment-4568205
Share on other sites

The Timing Belt should have been changed when the car gets to 100,000km's.

Usually they are changed just before the 80,000km's mark.

Best to change it if you don't know if it has been done or not and since you got to 112,000km's, it be a good time to change it.

Link to comment
https://www.sau.com.au/forums/topic/266379-r33-timing-belt/#findComment-4568598
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
    • Hi,  Just joined the forum so I could share my "fix" of this problem. Might be of use to someone. Had the same hunting at idle issue on my V36 with VQ35HR engine after swapping the engine because the original one got overheated.  While changing the engine I made the mistake of cleaning the throttle bodies and tried all the tricks i could find to do a throttle relearn with no luck. Gave in and took it to a shop and they couldn't sort it. Then took it to my local Nissan dealership and they couldn't get it to idle properly. They said I'd need to replace the throttle bodies and the ecu probably costing more than the car is worth. So I had the idea of replacing the carbon I cleaned out with a thin layer of super glue and it's back to normal idle now. Bit rough but saved the car from the wreckers 🤣
    • After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
×
×
  • Create New...