Jump to content
SAU Community

Recommended Posts

Yo, Ive got a '95 R33 GTR here in sydney for wrecking as it unfortunately can't be complied

It's silver and has approx 44,000 ks, series 1. I can post almost everything from the car, or pickup is available. Will post some more pics in the next few days

R33 GTR rb26dett motor, complete engine with approx 44,000 ks. Compression test came up perfect- ~165-170psi each cylinder

Includes turbos, wiring loom, ECU, manifolds, injectors - $5000 ono

post-35556-1240394181_thumb.jpg

17x9" Axia? (jap wheels) +18 offset wheels with Dunlop Lemans LM702 tyres, front 2 have about 50% left, rears are pretty much on the tread markers

$1000 ono

post-35556-1240393750_thumb.jpg

5sp Manual GTR box, good nick.. includes slave cylinder, shifter - $1000

HKS 3" catback exhaust - $200

Exterior stuff

R33 GTR front bar - paint is cracked + grazed a bit on drivers side. includes blinkers - $400

R33 GTR grille - $250

R33 GTR front guards, includes GT badges and blinkers - $500 pair

S1 headlights - $400

R33 GTR front reo bar - $150

radiator support/ nose cut - $300

R33 GTR sideskirts + rear pods - $200

R33 GTR bootlid + spoiler. Paint is a bit faded on the pass side near windscreen, includes GTR badge - $400

Rear 'Skyline' garnish - $50

Guard liner plastics, both sides - $100

Brake vent plastics - $100 pair

Tail lights - $50 each

Side mirrors - $50 each

Passenger door minis door trim - $150

Drivers door minus door trim/switches - $200

post-35556-1240393680_thumb.jpg post-35556-1240393701_thumb.jpg post-35556-1240393200_thumb.jpg

post-35556-1240393715_thumb.jpg post-35556-1240393732_thumb.jpg post-35556-1240393766_thumb.jpg

Engine bay stuff

R33 GTR afms - $200/pair

R33 GTR airbox & snorkel - $150

Engine Mounts - $100/pair

GTR BM-57 brake master cylinder - $120

Stock dump pipes + front pipe - $150

Stock BOV pair - $120

Stock BOV recirc piping - $100

Stock FMIC piping - $100

Stock Calsonic FMIC, some damage to the bottom though it still holds pressure fine - $50

R33 GTR A/c condenser - $150

R33 GTR radiator- $100

Thermo fan - $80

GTR Washer bottle - $30

fuse box lid - $20

radiator overflow bottle - $20

Charcoal canister - $30

Bonnet lining - $50

post-35556-1240393555_thumb.jpg post-35556-1240393670_thumb.jpg post-35556-1240393834_thumb.jpg

Suspension/brakes/driveline

Front & rear Brembo calipers + pads - $1750 full set ONO

Stock suspension, full set - $250

GTR front + rear swaybars - $150

GTR rear diff - $500

standard swaybars - $80 each

Front upper control arms - $50 each

Rear lower control arms - $50 each

Rear 5 stud hubs - $160 pair

Handbrake assembly & cables - $160 pair

17" space saver tyre - $50

post-35556-1240393229_thumb.jpg post-35556-1240393783_thumb.jpg

Interior stuff:

post-35556-1240393307_thumb.jpg

R33 GTR front + rear seats + door trim, complete set - $1600 ono, will probably seperate

GTR instrument cluster, carbon fibre look cover ~44,000ks - $250

GTR 3 gauge centre DIN cluster, nismo white face cluster & carbon fibre look cover - torque, oil temp and boost - $175

post-35556-1240393321_thumb.jpg post-35556-1240393332_thumb.jpg post-35556-1240393294_thumb.jpg

Steering wheel with S1 airbag (some wear on the wheel but airbag is great) - $150

Complete Boot interior - $100

Drivers door window switch (suit s1/s1.5 R33) - $80

Drivers window switch surround (s1), bit worn - $30

Drivers door window motor - $80

Passenger door window motor - $50

Large dash surround plastic with clock etc (s1) - $70

Gear stick surround (s1) - $50

Ashtray - $25

Glovebox - $40

climate control - $40

Seatbelts, full set - $80 (will seperate)

If you're after any random bits and pieces that arent listed, shoot me a PM- got the whole car available

Cheers!

Link to comment
https://www.sau.com.au/forums/topic/266621-r33-gtr-95-wrecking-in-sydney/
Share on other sites

  • Replies 140
  • Created
  • Last Reply

Top Posters In This Topic

front guards on hold till next week! climate control sold pending payment

pm sent

Replied

pm sent

replied

pm sent

replied

how much for the front Strut Brace?

oops, forgot to list it - $80 each for the strut braces

pm replied!

pm sent

replied!

Post the brake ducts to Melb?

yep no worries, PM sent

Pm Sent

replied!

il take the head lights and grill , also the airbox and afm please pm me

done, PM sent

PM Sent!

replied!

how much for just the front gtr seats? any damage ie. rips and so on

Chasing $1000 for the front 2 seats+rails. No rips or anything, few tiny tiny marks but theyre negligible imo

pm sent

replied!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • jeebus. glad you weren't under it while performing the stunt. Also thanks for the link to the wheel measurer, exactly what I needed
    • In the older stuff there were very significant differences 2wd to 4wd, for example Stagea had strut front end for 2wd and double wishbone for 4wd so it was not minor to swap. From poking around the 2wd v37, it *looks* like it might be more possible; some of the parts specifically have "2wd" stamped on them which suggests the platforms are more similar. You'd still want to start with a 4wd half cut to swap stuff from though. I'd suggest if you don't have a tune on the ECU you don't really need one on the trans either. Throttle mapping is in the ECU side (and you can always use a Roar Pedal if you want the throttle to actually respond to your foot), and really if you are happy with the stock power you probably accept the stock trans behaviour too....its all made to be "sporty" not racey.
    • So, updates. I have not washed the car since it came back from Tassie. I've driven it around a bit but not got around to actually sorting it out. I DID raise it because I cracked the rear bar leaving a hotel which was very distressing. Interestingly, the car drives more compliant now that it's raised a fair bit (5mm front, 15mm rear). Also noticed that my FR height was 10mm lower than FL. So that's now sorted out, too. I also bought this and had it printed: https://www.etsy.com/au/listing/1576422240/wheel-and-tire-fitment-tool-universal?ref=shop_home_feat_1&dd=1&logging_key=08f604d9fa4cc383550ba985e6ac85cd5cac7fbb%3A1576422240 Now, if I was smart I would have taken my brake calipers off to actually use this correctly but it was evident enough to me that in the region where the caliper was... there was nothing to hit suspension/guard/arm wise. So I'm going with "it'll be fine" after using the tool to hopefully very precisely measure the wheel clearance. Also while doing this, I had the very VERY bad idea of jacking one of the wheels/suspension arms up while the rest of the car was on jack stands. I did this to see how the arm would travel. This all was well and good until the car slid off the stands and went through a fence. So don't do that. Incredibly nobody was hurt and there was only minor damage to the rear bumper as the car didn't have far to slide, and had 3-4 wheels on it. The only damage turned out to be the fence itself which was easy to fix, and a little bit of damage to the fibreglass rear bumper trim. I had already planned to try a touch up paint kit to fix the time I drove into my garage door to see if it'd help in the interim before I get it fixed properly. I used the Dr Colorchip kit after looking online and seeing everyone talking about it. Yes it's made for chips and not huge broken missing pieces and I'll be 500% recommending it for stone chips after using it for stupid things like me. This took about ... 10 minutes and looking at the half assed photo the 30 second job I did on the bumper corner was almost perfect just by using the tiny little brush and painting it in. The sealact stuff to remove over-painting is really useful, so if/when I do it again I'll likely slather the touch up paint well over it and then clean it up with the cleaning solution. The wheels should arrive in a couple of weeks. I am still kinda confident after doing a stupid amount of measuring (and borrowing a set of 18x10.5+15) that they will not fit because I overlooked something, somehow and flew too close to the sun. ALSO R34 GTR guard liners do not fit on a GTT. I bought the undertray brake duct guides and had the wonderful problem of them not fitting my intake, my oil cooler and the liners themselves were even worse. Attempting to fit them won't work in general - You would have to cut them up as another poster mentioned as the bodywork is different on the GTT. At least I can try to resell them. So instead of cutting those up, I cut up my old already-cut-up GTT liners and extended them by using some PP plastic and drilling some 8mm holes for some nissan clips for the 'extra' bit. Because I was happy to cut them I was able to mount them pretty damn forward so I now have some semblance of guard liners, and the brake vents seal the bumper from the bottom. It sort-of-looks like this, to give some idea - If you look at the GTR and then the GTT this is when I realised that I needed to seriously measure as the inside of the rim area is entirely, entirely, entirely different and could not take any internet measurements for granted.   
    • If you are Ecutek tuned then these TCU tunes are anywhere from $550 to $700 usd. If you are not ECUTEK tuned, then it gets costly!    
    • Sorry to hear your HFM BM57 was faulty,  did you contact HFM I would hope they would be at least grateful for the information if there was some sort of manufacturing fault, you would hope they would be sympathetic even if your item was 2 years old if it had never been fitted. May I ask where it leaked from ?
×
×
  • Create New...