Jump to content
SAU Community

Recommended Posts

I stand to be corrected, but I think R34 and R33 rails are the same - should bolt on perfectly...however, I think R33 seats are slightly larger so you may have some issued with fitment in regard to the space between the seats and the center arm rest.

Link to comment
https://www.sau.com.au/forums/topic/266918-seat-queries/#findComment-4554279
Share on other sites

what sort of rails would u need to run gtr seat in a gtt or could u just modify them.

in my s14 i put s15 seats in them and had to bend one of the rails to fit them in could u do something similar with the gtr seats as i dont really like the bride or sparco seats (im a big unit)

Edited by GUN_METAL_GTR32
Link to comment
https://www.sau.com.au/forums/topic/266918-seat-queries/#findComment-4556313
Share on other sites

Hi adrian_r34 or should I say Jess R33,

It’s quite amusing how similar the both of you are:

adrian_r34 joined 24/04/2009

Jess R33 joined 20/04/2009

Jess R33 has an Apexi Power FC with HC to sell….from her Series 1 R33 which was recently “EPA’d”

http://www.skylinesaustralia.com/forums/Po...96#entry4545796

and so do you from your recently “upgraded” Series 1 R33 to a 34gtt

http://www.skylinesaustralia.com/forums/Pa...17#entry4553917

Jess R33 was also speaking of selling her standard r33 gtst series 1 driver’s seat in the same post

http://www.skylinesaustralia.com/forums/Po...96#entry4545796

and you….well…. you were quite interested in seats too….

http://www.skylinesaustralia.com/forums/Se...52#entry4554152

BUT the part that seals the deal for me is that the two of you have the same IP address…..

So….I think you need to have a little think, speak to your housemate (who you posted also has a R33)…..and let me know what you want to do…via post or PM…

What I would like is my $1200 back ASAP.

I will be contacting the police as well as DOCEP (Department of Consumer Protection) if you don’t get back to me.

Peter

Link to comment
https://www.sau.com.au/forums/topic/266918-seat-queries/#findComment-4569033
Share on other sites

  • 1 month later...

hey.

Can someone please tell me if skylines and stageas have the same seat rails? (except for the 34 which we now all know are different :()

I just want to know if I can put 33gtr seats into a series 2 stagea and I have searched, honest, but I just can't find an exact answer. I've found bits about people putting gtr seats into stags but it doesn't say if the rails are all the same or if you need new ones.

Any advice would be greatly appreciated.

Thanks

Link to comment
https://www.sau.com.au/forums/topic/266918-seat-queries/#findComment-4682314
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hope you aren't too sore after that one, might take a day or 2 to notice yet and I guess it is a loooooong drive home. On the bright side, tube frame front end is a thing at superlap, right?
    • https://www.facebook.com/share/p/18rmVb1SKB/ 
    • The chart of front pressure to rear pressure (with one being on the x axis and the other being on the y axis) is not a straight line on a typical proportioning valve. At lower pressures there is a straight line with one slope, and at higher pressures that changes to a lower slope. That creates a bend in the line at that pressure, called the knee point. If you do not change the proportionng as the pressure gets higher, you will suffer excessive pressure (at one end of the car or the other, depending on which way you look at the proportioning action) and then get lockups at that end. The HFM BM57, from my memory of previous discussions, is based on the BM57 from a different car (to a Skyline), with a different requirement for the location of the knee point and the distribution of pressure front to rear, and so is not a good choice for an upgrade on a Skyline. Here's a couple of links to some old posts, one from here, one from elsewhere. A lot of it pertains to adjustable prop valves, but the idea is the same. There are plenty of discussions on here about this issue from al the many years of people wanting a cheap/accessible option. https://grassrootsmotorsports.com/forum/grm/learn-me-brake-proportioning-valves/236880/page1/ https://grassrootsmotorsports.com/forum/grm/learn-me-brake-proportioning-valves/236880/page1/  
    • Yeah dunno why johhny posted that here with no context, just post on FB/insta bro where he put it up?  Laine had an off at T4 during Thurs prac, he's ok, car is less than perfect, they are done for the weekend, he can fill in the rest. Bando also binned it like 100m up the road.   
    • I feel there must have been a FB/insta post and the weekend did not start well at all I hope everyone is all okay
×
×
  • Create New...