Jump to content
SAU Community

Mrs Fatz Skidz And Track Beeratch

fatz

By fatz,
in Motorsport Discussion & Builds

 Share

Recommended Posts

  • Replies 192
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

fatz Grand Master

fatz

Posted
  • Author
Posted

might even drive alright once its had an alignment

the day after it was registered it was at the track

ive already told jenna to start saving 10k for the new engine

lol

and ive discovered that it cant rip a 3rd geaar bunout at its current power level

:rolleyes:

Beer Baron Grand Master

Beer Baron

Posted
Posted

fark 137kegs you will look positively anorexic.

no need for $10K engine. I have a nice, complete RB26 out of a 1994 R32, wide crank drive, excellent compression, all yours for $3750. guaranteed to chirp something...

Beer Baron Grand Master

Beer Baron

Posted
Posted

beer baron need money. hence RB26 out the door! :P it's fully running and with good compression (had it checked before it was pulled out of the car). has a brand new sump on it too as it was replaced with a new R34 N1 Nur motor and for ease of install we took the sump off the 32 motor and slapped it onto the 34 motor. it wasn't out of a wreck or anything. Just clean 1994 R32 GTR we bought and put a new N1 Nur motor in. anyway, if anyone wants it I'll be putting up a FS thread soon.

Beer Baron Grand Master

Beer Baron

Posted
Posted

that's a big 10-4. 32 diff gears are plentiful though if needed for anyone.

in a slightly related matter I just got a line on sets of brand NEW 4.375:1, R32 GTS4 diff gear sets for front and rear (both crown wheel and pinions). they are not much more than the $$$ people charge for second hand ones to poor GTR owners like me.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      RB25DE NEO with Haltech ECU

      By MBS206 · Posted

      You very likely need to get it on a dyno and tune it. My assumption is, you've got an RB25DET tune in it, which has a different manifold, different injectors, and different cams as a minimum. What O2 sensor are you running?   When you say it runs extremely rich from idle all the way to redline, is this just free revving it you see that?
    • Haggerty
      RB25DE NEO with Haltech ECU

      By Haggerty · Posted

      I seem to the be only person that is using a Haltech 2500 on an NA motor, I've installed a Bosch DBW throttle body to the OEM intake manifold and am having problems maintaining AFR even with the wideband o2.  It will run extremely rich at idle and up to redline, but under load it will go extremely lean in the 20s and i'm essentially having to rev it over 4k and feather the clutch to get it up to speed.  I've read a few other threads of about the butterfly, it seems removing the vacuum to it is supposed to have it remain open, i've noticed no difference under 4k with the vacuum line to it plugged.  I'm hoping someone here has had luck using the NA manifold with Haltech, and if they happen to have a tune for it.  
    • sonicii
      Could it really happen......

      By sonicii · Posted

      I don't know any details, but I really wouldn't be surprised if they do it as a LHD only version, at least initially.
    • Gareth87
      What should I do next to hold the head on

      By Gareth87 · Posted

      Thanks for the replies everyone. Definitely a coolant push. Oil catch can is empty and always has been. As the engine is out now I'll be having a good look over things. I do have some detonation on the piston tops from a trigger issue back about 5 years ago. I felt it and shut off then bought a new ecu and changed the trigger. Never been an issue since. It never hurt the power, its made almost 80hp more since that incident but I will pull the bearing caps to take a look. If the bearings are damaged I will do a bottom end refresh. Head is being re conditioned at the moment and the block will be cleaned and checked to ensure it's flat. I'll go with a kameari gasket and see how it ends up. The other thing I'm not super keen on is the cylinder colours. I suspect this is from the inlet manifold. The plan will be to put it back together, retune and then stick a plazmaman billet inlet on it and retune. I'm happy with the power, if it makes a little more, then great, but I would rather just make everything more efficient at this stage.
    • MBS206
      Could it really happen......

      By MBS206 · Posted

      Maybe they'll look to do a bunch of presales to help inject some cash fast for their financial issues...
×
×
  • Create New...