Jump to content
SAU Community

L24et C210 Coupe Parts Fire Sale!

Silent Shadow
 Share

Recommended Posts

Factory 5 Mentor

Factory 5

Posted
Posted

nick, the guy who had it years ago dropped in a L24e from a series 2 MR30 skyline

his username was 'Neg'

the sump comes standard with a flat section on the side for an oil return to be welded on

the water line part is likely the part that heats up the idle control valve or throttlebody

unfortunatlryeh its just a stocko L24e, but the head has been recoed a while back, new gaskets etc

the rings are the buggered part...

the reason it kept popping was the microtech fuel only ecu was what was contolling well only fuel... not ignition at all!, the dizzy didnt retard timing on boost, so ping ping away

I will use the stock L20et gear, which is the 1st Nissan ECCS 'JECS' ecu setup, that does change timing, and fuel etc (but i will be useing the microtech as a piggyback for the minute)

noddle Rising Star

noddle

Posted
Posted
I will use the stock L20et gear, which is the 1st Nissan ECCS 'JECS' ecu setup, that does change timing, and fuel etc (but i will be useing the microtech as a piggyback for the minute)

Use Megasquirt if you have the time and money. works great with fuel and timing..

Nigel

noddle Rising Star

noddle

Posted
Posted (edited)
would do, but not got the cash, plus its bloody confusing what to use, ms1 v3 or all that....

hey you can help though!!

It's easier now, been there done that,

MS 1 or MS II is the CPU type (depending on what code you going to run as well I believe), I'm using MS II on the v3.0 board over the older v2.2 board, the v3.0 can support direct drivers, which I'm not using, but I believe you can control the coil(s) directly from the v3.0 board, the 2.2 board had to have extra hardware (fly back board I believe) .

when I did mine, I just uses MS for fuel, running the original dissy, then later I set-up waste spark, but the instructions (manual), are well done, easy step by step (as long as you know what you want). the actual first time set-up was a little over wheeling, but if you go through the manual it has answers for 95% of what you need. it would also help if it wasn't your Daily Drive, so you don't stress out if it's not doing what you want it to do.

Nigel

Edited by noddle
racsov500 Grand Master

racsov500

Posted
Posted
nick, the guy who had it years ago dropped in a L24e from a series 2 MR30 skyline

his username was 'Neg'

the sump comes standard with a flat section on the side for an oil return to be welded on

the water line part is likely the part that heats up the idle control valve or throttlebody

unfortunatlryeh its just a stocko L24e, but the head has been recoed a while back, new gaskets etc

the rings are the buggered part...

the reason it kept popping was the microtech fuel only ecu was what was contolling well only fuel... not ignition at all!, the dizzy didnt retard timing on boost, so ping ping away

I will use the stock L20et gear, which is the 1st Nissan ECCS 'JECS' ecu setup, that does change timing, and fuel etc (but i will be useing the microtech as a piggyback for the minute)

interesting. I was wodering what the go was with the 2.4l block and how the turbo gear was only on 2 litres.

I need a pair of good coupe doors. would be alot easier then fixing the ones on it. anyone help?

harvo Collaborator

harvo

Posted
Posted
Harvo, what are putting that supercharger on?

On the Datto if it'll fit, have to get the tape measure out and check first :D

Make or modify a pulley system, and finish off an adaptor for a 310 Holley.

Maybe a cam grind too.

Just doing it for something to do, waiting for cheap parts to come up and making use of the gear at work that's available to me. I wright it off as being "essential for my apprenticeship" hahah

Cheers Dan.

  • 3 weeks later...
Silent Shadow Rising Star

Silent Shadow

Posted
  • Author
Posted
What ever happened to this car cam?

Sucks that it had to be parted! by the way i only did 3 hours driving on that head and it was fully reco'd

hope it didn't go to waste :(

nope not a waste at all mate. helped me successfully convert my car to manual and got a few good bits from it where my orange car failing. good stuff! im happy all the stuff went to good homes.

people are still ringing me about the car. it's gone peeps! sorry.

racsov500 Grand Master

racsov500

Posted
Posted

ive got it now. want to get it road going again but it will take bulk time, effort and coin, and lot of parts searching. ive got a buildup thread on auszoku which ill update whenever I do something.

someone buy this. or trade me something I need. like doors or a gearbox / tailshaft or something. or a running carby 2.4.

c210010.jpg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Black_CSR
      Wheel Sizes & Offsets For Skylines

      By Black_CSR · Posted

      ok so if i wanted to go 18's i would go for 8's  in front 30+ or 32+ off set at front and the back 9 would be ok? what offset should i aim for.. then can i do some  hunting for wheel rim choices..    If i get this - will this fit all around: Size: 18 x 8.5 +37 - n what tyres size tyre should i get for front n back?  
    • GoHashiriya
      From Japan and back to Europe, my sh*tbox R34 GTT

      By GoHashiriya · Posted

      Absolute f*cking nightmare. I had to take breaks constantly, and I was always pissed off when I got home. The line split in Italy on day 2 (we drove from the Netherlands), lol. Driving any narrow European town was... well, sh*t.   Appreciate it man. Here, I'll just drop a favourite from the load I took on Saturday.   I'll update here when things happen with the car, the thing is, with stock power and almost everything chassis-wise taken care of, there really are no problems. 268,000kms now and counting.  
    • Kinkstaah
      WTB R34 GTR Guard Liners

      By Kinkstaah · Posted

      Ah! I actually managed to snag a lightly used set.... that aren't so suitable for me right now. They don't work on a GTT without some cutting or creative heat moulding. I thought about reselling them myself cause I didn't want to murder them, but it looks like I'm probably going to attempt to murder them/melt them because I may as well. @GTSBoy @PranK can somebody close this thread?
    • itsmeyo
      WTB R34 GTR Guard Liners

      By itsmeyo · Posted

      Hey mate,  I have a set, one is slightly damaged but wont be noticable once installed.  Shoot me a message if your still after them 
    • The Bogan
      NC MX5

      By The Bogan · Posted

      I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
×
×
  • Create New...