Jump to content
SAU Community

Recommended Posts

  • 4 weeks later...

Any more pics of this car ? What specs are you running ?

Hey they are 18*9 rear + 35 and 18*8.5 + 35 fronts.

Fronts sit way to far in sadly.

new rims coming now anyway...

DUBS BRO

20 inch meisters lol

New ridiculous look for my car

20 * 9.5 +25 Work Meister S1's.

Unsure what the front offsets will be, pick them up Monday

iphone950.jpg

Quite obviously not slammed/cambered yet

  • 2 months later...

Yeah, was looking so clean till i spotted those. Clean then up?

I ran Work meister's on my 1.5 M, but they were 17's so they always looked a tad small, if i had wheel choice for it again i would have gone 18x9 front and 19x10.5 rear, but SSR SP1 instead of heavy meisters.

Edited by dub step is love
  • 3 weeks later...

wtf is with your old rego sticker reminants man?

Yeh I'm lazy, and Qld can't make a decent fricken sticker

I personally love this set....

Anyone knows what are these wheels called?

163177394_full.jpg

Look like Enkei GTC01 - but I've never seen them that concaved.

they are DotCom racing wheels.

the car is for sale too here

they are one of the best sets of wheels ive seen on a 33, besides mine haha thumbsup.gif

lol, thanks for the info.

Hm... I can't find anything about DotCom Racing wheels on google, any idea where you can get those from?

Thanks

Here's mine.. Super Advans 18's 9.5 +32 Front n Rear. 235's front n 265 rear. The Front left rubs a little after raising it by 25mm.. the right doesn't as it sits a little bit higher, but this only happens if i'm going fast around a corner.. perhaps -2.5 camber will help?

post-26455-0-44281400-1301936235_thumb.jpg

post-26455-0-94603400-1301936266_thumb.jpg

post-26455-0-52666600-1301936285_thumb.jpg

Edited by Black_CSR

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Thanks MBS206, i got that PDF but got abit overhelm with all the connections and tracing of wires. I wasn't expecting to plug the dash harness anywhere. i was just going to use my electronics jumper wires to plug into the right pins like ECU power, ecu ground, ignition trigger etc... I do have a few ratchet straps locking it down tight. Fire extinguisher ready and only a small amount of fuel at a time, enough to submerge the pump.
    • Thanks GTSBoy, i will do abit more digging. I am missing a blue relay near the ECU connector... so i will chase that up in the next few days as well  
    • https://yariksteel.ru/manual/R33/Skyline_R33_elektroprovodka.pdf   Page 18 should be what you want for the Dash Cluster wiring. Though, you don't need the dash plugged in to get the motor running. What you want is power as how GTSBoy said. You need to power the ECU. Find in the above link the ECU pin outs (Verify them before just connecting them up from things written on the internet). Find anything needing power, give it power, find anything needing ground, give it ground. Then give the starter motor power through a big cable, and bridge the solenoid on the starter straight to power too.  ECU will be on, and when you give the starter power, it'll spin the starter motor, and it should start. I also hope you have a proper stand, and not just the engine sitting on some wood. You will want it bolted down properly.
    • Hello everyone, I am happy to join you.
    • Whereabouts are you, that looks exactly like Akira's old car....
×
×
  • Create New...