Jump to content
SAU Community

Recommended Posts

Photo's of my poor baby after going sideways through a roundabout. Didnt see it, no give ways signs or roundabout signs, a lamppost was out one was lit but it wasnt enough. Locked up the brakes the car went sideways as I tried to steer around the rounabout, blew the drivers side rear tyre and then beached itself on the far corner in some sand between the kerb and the footpath. It seems I was quite lucky, the sideskirt is beyond repair I think, and I had to put some new rubber on (so I went ahead and put the 2 18" rims I had on the rear) though it seems I need a wheel allignment as anything over 100km/hr and the wheel vibrates.

Link to comment
https://www.sau.com.au/forums/topic/26836-roundabout-carnage/
Share on other sites

Originally posted by skyzerr33

so whats it like to drive with the space saver?

Scarey. I wouldnt want to be driving on it too much, cant do more than 80km/hr and even then I was only doing 70km/hr just to make sure I got home ok. Seriously its about 1/4 the width of the new 265/35 rubber.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
    • Can I suggest you try EBC directly again and link them to as many competitor catalogues as you can to show their listing is incorrect, eg https://dba.com.au/product/front-4000-series-hd-brake-rotor-dba42304/ If you have access to an R33 GTST VIN and your VIN, you could also use a Nissan Parts lookup like Amayama to show them the part number is different between 33 GTST and 34 GTT which may get their attention
    • So i got reply from EBC and they just this site where you can clearly see those 296mm fronts on R34 GTT. I send them photos and "quotes" that 296mm are not for 34 GTT and they are too small. But it will be very hard to return them cuz nobody here knows 100% and they just copy those EBC catalogue :-D https://ebcbrakesdirect.com/automotive/nissan/skyline-r34
×
×
  • Create New...