Jump to content
SAU Community

What Is This -> Black Plastic Cover Where Rear Mud Flap Should Be?

mario
 Share

Recommended Posts

mario Contributor

mario

Posted
Posted

hey guys,

Giving the car a good ol' detail the other day and while I'm washing I get to the rear wheel wells, and notice at the back of the

sideskirt where you would imagine a mudflap to located, that general area, there is a small black plastic cover/casing that seems

to serve no purpose other than to hold up to the last 6months of driving worth of dirt / glass / bits n pieces of whatever you ever

drive over and from wherever.

I didnt try get under the car to remove it, but there seems to be no hole so it doesnt act as a drain, its literally just there for what

seems to me, to catch dirt and make my cleaning job longer than what I had anticipated due to the amount of dirt that came out

of it.

Anyone able to shed some light on what this might actually be there for ?

You can almost bend it 120degree's to try remove the dirt it holds, and it wont snap or break and will just go straight back to its

original position also.

Be interesting to see what other people say/ think or even knew if it was there..

mario Contributor

mario

Posted
  • Author
Posted

time is limiting factor here with photos unfortunately, that and the fact it would be all black on black if I took something..

quite simple really... go to the rear wheel well of your car, you can see where the side skirt finishes, put your hand inside the wheel well

right behind the skirt and you will feel this big black plastic cover that is open at the top..

you can stick your fingers into the hole it creates, then you realise you can bend it back and all of a sudden you notice all the dirt n crap

it holds in it....

rs73 Grand Master

rs73

Posted
Posted

how would that work?

I didn't remember seeing anything around the door jamb when the doors were opened that could indicate some path of air to escape if that's to equalise the pressure...

maybe just a bad design, and they decided to put a plastic cover on top to reduce the whole crap load of sh1t it would have collected without the cover?

boodsGtr Enthusiast

boodsGtr

Posted
Posted
how would that work?

I didn't remember seeing anything around the door jamb when the doors were opened that could indicate some path of air to escape if that's to equalise the pressure...

Not necessarily from the door jam. Some cars have them so when you close the doors, the cabin pressure that builds up when you close the door is released through a vent at the rear, enabling the door to be closed easier.

Might not be the case for this, but a possibility.

Boods.

  • 2 weeks later...
scathing Grand Master

scathing

Posted
Posted (edited)

Is it behind the wheel? Almost like a L-shape when viewed from side on (a vertical piece, with a flat horizontal tray) where the horizontal bit is a quarter circle?

There'll be one on either side of the car, but have different shapes.

Edited by scathing
BLISTC Experienced

BLISTC

Posted
Posted
Is it behind the wheel? Almost like a L-shape when viewed from side on (a vertical piece, with a flat horizontal tray) where the horizontal bit is a quarter circle?

There'll be one on either side of the car, but have different shapes.

you still have not helped us solve the mystery... what does it do!?

mario Contributor

mario

Posted
  • Author
Posted
Is it behind the wheel? Almost like a L-shape when viewed from side on (a vertical piece, with a flat horizontal tray) where the horizontal bit is a quarter circle?

There'll be one on either side of the car, but have different shapes.

yeah thats it, no idea wtf it does or why it there though

scathing Grand Master

scathing

Posted
Posted (edited)
you still have not helped us solve the mystery... what does it do!?

Just making sure I'm talking about the right thing first. :(

yeah thats it, no idea wtf it does or why it there though

It is probably the OEM rear diffusers. They smooth the airflow leaving the rear wheel well.

On the Australian delivered 350Z, it's standard on the Track and optional on the Touring (I ended up picking up a set for my Touring from the USA). Apparently the Touring has a Cd of 0.30, and the Track (with a small chin spoiler, rear bootlid spoiler, and these rear diffusers) drop the Cd to 0.29.

When I spoke to Pro Concept about it they told me they took theirs off their race car. Like you, Josh said the only thing they were good for is collecting dirt whenever they came off the track. If it takes those 3 items above to drop the drag co-efficient by only 0.01, taking them off will probably do sweet f**k all.

Edited by scathing

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Turbodoc
      Noobie Stagea owner..

      By Turbodoc · Posted

      Hey Dave, welcome aboard! Good to see another soon-to-be Stagea owner here. The wagons are awesome — plenty of space, still got that Skyline DNA, and loads of potential if you’re into mods. Definitely post up pics when you get it, everyone here loves seeing new builds. What model/year are you looking at?
    • GTSBoy
      Duncan's V37.......race car?

      By GTSBoy · Posted

      See if you can thermal epoxy a heatsink or two onto it?
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      The other problem was one of those "oh shit we are going to die moments". Basically the high spec Q50s have a full electric steering rack, and the povo ones had a regular hydraulic rack with an electric pump.  So couple of laps into session 5 as I came into turn 2 (big run off now, happily), the dash turned into a christmas tree and the steering became super heavy and I went well off. I assumed it was a tyre failure so limped to the pits, but everything was OK. But....the master warning light was still on so I checked the DTCs and saw – C13E6 “Heat Protection”. Yes, that bloody steering rack computer sitting where the oil cooler should be has its own sensors and error logic, and decided I was using the steering wheel too much. I really appreciated the helpful information in the manual (my bold) POSSIBLE CAUSE • Continuing the overloading steering (Sports driving in the circuit etc,) “DATA MONITOR” >> “C/M TEMPERATURE”. The rise of steering force motor internal temperature caused the protection function to operate. This is not a system malfunction. INSPECTION END So, basically the electric motor in the steering rack got to 150c, and it decided to shut down without warning for my safety. Didn't feel safe. Short term I'll see if I can duct some air to that motor (the engine bay is sealed pretty tight). Long term, depending on how often this happens, I'll look into swapping the povo spec electric/hydraulic rack in. While the rack should be fine the power supply to the pump will be a pain and might be best to deal with it when I add a PDM.
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      And finally, 2 problems I really need to sort.  Firstly as Matt said the auto trans is not happy as it gets hot - I couldn't log the temps but the gauge showed 90o. On the first day I took it out back in Feb, because the coolant was getting hot I never got to any auto trans issues; but on this day by late session 3 and then really clearly in 4 and 5 as it got hotter it just would not shift up. You can hear the issue really clearly at 12:55 and 16:20 on the vid. So the good news is, literally this week Ecutek finally released tuning for the jatco 7 speed. I'll have a chat to Racebox and see what they can do electrically to keep it cooler and to get the gears, if anything. That will likely take some R&D and can only really happen on track as it never gets even warm with road use. I've also picked up some eye wateringly expensive Redline D6 ATF to try, it had the highest viscosity I could find at 100o so we will see if that helps (just waiting for some oil pan gaskets so I can change it properly). If neither of those work I need to remove the coolant/trans interwarmer and the radiator cooler and go to an external cooler....somewhere.....(goodbye washer reservoir?), and if that fails give up on this mad idea and wait for Nissan to release the manual 400R
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      So, what else.... Power. I don't know what it is making because I haven't done a post tune dyno run yet; I will when I get a chance. It was 240rwkw dead stock. Conclusion from the day....it does not need a single kw more until I sort some other stuff. It comes on so hard that I could hear the twin N1 turbos on the R32 crying, and I just can't use what it has around a tight track with the current setup. Brakes. They are perfect. Hit them hard all day and they never felt like having an issue; you can see in the video we were making ground on much lighter cars on better tyres under brakes. They are standard (red sport) calipers, standard size discs in DBA5000 2 piece, Winmax pads and Motul RBF600 fluid, all from Matty at Racebrakes Sydney. Keeping in mind the car is more powerful than my R32 and weighs 1780, he clearly knows his shit. Suspension. This is one of the first areas I need to change. It has electronically controlled dampers from factory, but everything is just way too soft for track work even on the hardest setting (it is nice when hustling on country roads though). In particular it rolls into oversteer mid corner and pitches too much under hard braking so it becomes unstable eg in the turn 1 kink I need to brake early, turn through the kink then brake again so I don't pirouette like an AE86. I need to get some decent shocks with matched springs and sway bars ASAP, even if it is just a v1 setup until I work out a proper race/rally setup later. Tyres. I am running Yoko A052 in 235/45/18 all round, because that was what I could get in approximately the right height on wheels I had in the shed (Rays/Nismo 18x8 off the old Leaf actually!). As track tyres they are pretty poor; I note GTSBoy recently posted a porker comparo video including them where they were about the same as AD09.....that is nothing like a top line track tyre. I'll start getting that sorted but realistically I should get proper sized wheels first (likely 9.5 +38 front and 11 +55 at the rear, so a custom order, and I can't rotate them like the R32), then work out what the best tyre option is. BTW on that, Targa Tas had gone to road tyres instead of semi slicks now so that is a whole other world of choices to sort. Diff. This is the other thing that urgently needs to be addressed. It left massive 1s out of the fish hook all day, even when I was trying not too (you can also hear it reving on the video, and see the RPM rising too fast compared to speed in the data). It has an open diff that Infiniti optimistically called a B-LSD for "Brake Limited Slip Diff". It does good straight line standing start 11s but it is woeful on the track. Nismo seem to make a 2 way for it.
×
×
  • Create New...