Jump to content
SAU Community

Fuel Pressure Regulator Or 740cc Injectors

Turbz RB-25
 Share

Recommended Posts

Turbz RB-25 Experienced

Turbz RB-25

Posted
Posted

Hi Fellas,

At the moment, I have nismo 555cc injectors. I currently have 311 rwkw but will be putting more boost in the car soon to get around 370 rwkw and I will need a slight fuel upgrade.

My tuner suggest putting a fuel pressure regulator on the car rather than get 740cc injectors, what do you guys thinks?

WHat are the advantages and disadvantages of both?

First difference is price I guess, injectors are $900 where as FPR is $160.

Is there disadvantages associated with running a FPR?

THanks fellas

2LV8ETR Mentor

2LV8ETR

Posted
Posted
My tuner suggest putting a fuel pressure regulator on the car rather than get 740cc injectors, what do you guys thinks?

Is there disadvantages associated with running a FPR?

The NisMo 555cc should be good for between 260-330kw. My belief is that you are running them close to their full potential. Go the 700cc if your budget will allow you to eat.

The only disadvantage with an FPR is that sometimes heat will cause them to crap out. This of course depends on the brand. The Malpassi rising rate FRP's are known for this. Keep it away from your exhaust manifold (The fuel lines are in the intake side) and you should be good.

blind_elk Grand Master

blind_elk

Posted
Posted

You can, generally, fairly safely increase the fuel pressure to the injectors with an adjustable FPR. But keep it sensible.

By increasing the fuel pressure, you get a much better spray pattern, and therefore better atomisation of the fuel in the mixture.

2LV8ETR Mentor

2LV8ETR

Posted
Posted
So are youu saying that with a FPR i wont be able to reach 370 rwkw?

Not with the 555cc's.

But for high power applications FPR's are a must.

While the pump provides fuel flow, the FPR will hold a given amount of pressure at the fuel rail. This is of course limited to the fuel pump used. The fuel pump must be able to supply the amount of fuel required by all the injectors in wide open throttle (WOT) conditions at the maximum boost level anticipated. A 20% safety margin (that is, the pump can supply 20% more fuel than is actually required) is often needed to avoid overheating the pump or a momentary lean mixture (and possible damage to pistons, valves, or rings). If the fuel pump is not up to the task, then the pressure will not be present at the rail, thus limiting the injector efficiency.

As the fuel pressure can impact on the amount of fuel discharged throughout the injector cycle it is vital that this pressure is kept constant and with this aim excess fuel is sent back to the fuel tank through the fuel return circuit located within the regulator.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Dose Pipe Sutututu
      From Japan and back to Europe, my sh*tbox R34 GTT

      By Dose Pipe Sutututu · Posted

      Welcome back brother 
    • GoHashiriya
      From Japan and back to Europe, my sh*tbox R34 GTT

      By GoHashiriya · Posted

      I got back to Japan in January and was keen to get back on track as quickly as possible. Europe is god-awful for track accessibility (by comparison), so I picked up a first-gen GT86 in December just to have something I could jump into right away. The Skyline came over in a container this time and landed in early January. It was a bit battered after Europe, though—I refused to do anything beyond essential upkeep while it was over there. The clutch master cylinder gave out, and so did the power steering. I didn’t even bother changing the oil; it was the same stuff that went in just before I left Japan the first time. Naughty. Power steering parts would’ve cost double with shipping and taxes, so knowing I’d be heading back to Japan, I just postponed it and powered through the arm workout. It took a solid three months to get the car back on the road. Registration was a nightmare this time around. There were a bunch of BS fees to navigate, and sourcing parts was a headache. I needed stock seats for shaken, mistakenly blew 34k JPY on some ENR34 seats—which, of course, didn’t fit—then ended up having the car’s technical sheet amended to register it as a two-seater with the Brides. Then there’s the GT86. Amazing car. Does everything I want it to do. Parts are cheap, easy to find, and I don’t care what anyone says—it’s super rewarding to drive. I’ve done a few basic mods: diff ratio, coilovers, discs, pads, seat, etc. It already had a new exhaust manifold and the 180kph limiter removed, so I assume it’s running some kind of map. I’ve just been thrashing it at the track non-stop—mostly Fuji Speedway now, since I need something with higher speed after all that autobahn time. The wheels on the R34 always pissed me off—too big, and it was a nightmare getting tires to fit properly under the arches. So I threw in the towel and bought something that fits better. Looks way cleaner too (at least to me)—less hotboy, less attention-seeking. Still an R34, though. Now for future plans. There are a few things still outstanding with the car. First up, the rear subframe needs an overhaul—that’s priority one. Next, I need to figure out an engine rebuild plan. No timeline yet, but I want to keep it economical—not cutting corners, just not throwing tens of thousands at a mechanic I can barely communicate with. And finally, paint. Plus a bit of tidying up here and there.  
    • The Bogan
      NC MX5

      By The Bogan · Posted

      Nope, needed to clearance under the bar a little with a heat gun, a 1/2" extension as the "clearancer", and big hammer, I was aware of this from the onset, they fit a 2.0 with this intake no problems, but, the 2.5 is around 15mm taller than a 2.0, so "clearancing" was required  It "just" touched when test fitting, now, I have about 10mm of clearance  You cannot see where it was done, and so far, there's no contact when giving it the beans Happy days
    • GoHashiriya
      From Japan and back to Europe, my sh*tbox R34 GTT

      By GoHashiriya · Posted

      It's been a while since I've updated this thread. The last year (and some) has been very hectic. In the second-half of 2024 I took the R34 on a trip through Germany, Italy, France and Switzerland - it was f*cking great. I got a little annoyed with the attention the car was getting around Europe and really didn't drive it that much. I could barely work on the car since I was living in an inner-city apartment (with underground parking). During the trip, the car lost power steering in France - split hose - and I ended up driving around 4,000kms with no power steering.  There were a few Nurburgring trips here and there, but in total the R34 amassed just shy of 7,000kms on European roads. Long story short, I broke up with the reason I was transferred to Europe for and requested to be moved back to Japan. The E90, loved it. It was a sunk cost of around EUR 10,000 and I sold it to a friend for EUR 1,500 just to get rid of it quickly. Trust me, moving countries f*cking sucks and I could not be bothered to be as methodical as I was the first time around.
    • MBS206
      NC MX5

      By MBS206 · Posted

      I assume clearances were all a-okay?
×
×
  • Create New...