Jump to content
SAU Community

Recommended Posts

Mine is a custom enclosure, technically, it sits where the spare tyre used to sit...

I've never had one above the fuel pump but that seems to cause alot of people problems. You'll probably find as well now that your RCA cables have been penetrated by the power and are creating noise, they will not shield as much anymore. Weird how it works like that but I've seen it happen a few times...

Can you ground your RCAs in any way? Normally the good ones have an extra cable running with them that you can ground to help minimise noise.

Here is a pic of my setup, completely useless to you, just thought I would share :DClicky!

Link to comment
https://www.sau.com.au/forums/topic/269049-rca-noise/#findComment-4582770
Share on other sites

i been trying diff grounds for amp no luck , bit better but noise does not go completely.

gets higher when i switch my lights on :D

i also tried relocating leads , only other way i can thing is if i run them thru middle of the car ...take passenger seat out and run rca's throught .

i cant ground my rca's , doof that setup is nice ;)

thanx for quick reply's boys

Link to comment
https://www.sau.com.au/forums/topic/269049-rca-noise/#findComment-4582785
Share on other sites

Crossovers will be fine. Do you have a spare set of RCAs? Even ones that aren't shielded?

Like I said, once the RCAs are corrupted, without getting new ones, you're going to have a tough time getting rid of the noise completely, but you have to sort it out or the same thing will just keep on happening.

What spec is the amp? And what grounds have you been trying? I would keep trying to find a good ground if I were you, maybe sand back some paint if it's stopping a good connection.

What about your battery? What's that like?

Link to comment
https://www.sau.com.au/forums/topic/269049-rca-noise/#findComment-4582822
Share on other sites

i got a new set of rca yesterday , amp is mtx maybe 6-7mnth old(about 60x4 rms)

i took the spare tyre out and there's few points where i sanded paint off and put ground there.

battery is standard.

did you run your rca and speaker cables together or yours are separate?

damn corrupt rca's hehe

i might try taking h/u out and checking if any of looms cables are cousing it but i doubt that.

Link to comment
https://www.sau.com.au/forums/topic/269049-rca-noise/#findComment-4582838
Share on other sites

I'm trying to remember how I did mine...

I ran a lot of wires up the middle but I forget which ones :D basically, I kept all RCA and any power wires very seperate (i think)... I've never had a problem.

My system is set up just a WEEEEE bit different to yours though... not a very good base for comparison at all.

Link to comment
https://www.sau.com.au/forums/topic/269049-rca-noise/#findComment-4582864
Share on other sites

i took the head unit out fiddled around a bit lowered noise tiny bit but once i turn my headlights on noise is back.

im getting sick of it , i think i will take the amp out and run the system off deck , i only run rears and fronts

the whine is killing me hehe

Link to comment
https://www.sau.com.au/forums/topic/269049-rca-noise/#findComment-4582927
Share on other sites

I've run RCA's next to speaker power wires, they are twisted pair RCA's though and I don't have an issue.

Not sure if it was the twisted pair construction which helped or not, I'd like to hear an opinion on that. The guys on Mobile Electronics seem to recommend twisted pair RCA's to prevent interference...

I also had what looked like car power wires running up the LHS and RHS of the car (battery in boot) I tried to keep away from them but the RCA's are pretty close, no issues though...

Link to comment
https://www.sau.com.au/forums/topic/269049-rca-noise/#findComment-4582957
Share on other sites

heres a few things to have a look at.

re-earth your car not just the amp.

That crappy earth wire that runs from the passenger inner guard to the exhaust manifold on a r33 needs to be replaced with something that is thicker and can handle more current difference.

Your head unit, a nice thick piece of graound cable from the chasis of the car to the chasis of the head unit.

Your power wire from the amp to the battery, move it away from the fuses and main feed for the car.

your earth wire on your amp - connect it to a different bolt in the boot than the factory earthing bolt under the battery.

make sure all the connectors you use are soldered, dont just rely on those crappy "gold" screw type connectors.

RCA's - twisted pair is a marketting ploy to get more $$ outta you. The amount of money you would need to spend on a system to hear an actual difference in RCA performance is more than you would spend buying a r33.

you can just always earth the outer sheilding on your existing rca's aswell..

if you do these basic's it should be fine as long you have good quality equipment.

My amp sits on a piece of timber mounted above a hi-flow intank fuel pump and the system has no noise to it.

Link to comment
https://www.sau.com.au/forums/topic/269049-rca-noise/#findComment-4582988
Share on other sites

to grond the rca's

you need to

- be careful

- cut through the plastic sheilding of the rca cable til you get the braided cable..(this goes to the outer part of the rca plug.. and it may also be a wire rather than braid on cheap rca...

- do not break this braid/wire - join another wire onto it

- becareful when soldering as to not burn through your rca's totally

- do near both ends of the rca cable

- once you have a wire soldered in at each in - earth each wire directly to the chasis

- do not earth them to other wires or amp/head unit earths.

thats about it, take your time and dont rush..

Link to comment
https://www.sau.com.au/forums/topic/269049-rca-noise/#findComment-4583095
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Can I suggest you try EBC directly again and link them to as many competitor catalogues as you can to show their listing is incorrect, eg https://dba.com.au/product/front-4000-series-hd-brake-rotor-dba42304/ If you have access to an R33 GTST VIN and your VIN, you could also use a Nissan Parts lookup like Amayama to show them the part number is different between 33 GTST and 34 GTT which may get their attention
    • So i got reply from EBC and they just this site where you can clearly see those 296mm fronts on R34 GTT. I send them photos and "quotes" that 296mm are not for 34 GTT and they are too small. But it will be very hard to return them cuz nobody here knows 100% and they just copy those EBC catalogue :-D https://ebcbrakesdirect.com/automotive/nissan/skyline-r34
    • Hi, is the HKS  Tower Bar still available ? negotiable ? 馃
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
  • Create New...