Jump to content
SAU Community

Recommended Posts

  • Replies 42
  • Created
  • Last Reply

Top Posters In This Topic

Are just as reliable as a piston engine when stock or modded correctly. They are an old car so if restored/rebuilt or looked after should be fine.

I wouldnt want one as a daily, too good. Maybe a rx7 series 3

Edited by pos513
basically i would really like a mazda rx 2 3 or 4.

how reliable would they be as a daily driver?

Same as any other car.

So long as it has been serviced regularly and doesn't have an obscene amount of ks it should be fine.

Have you considered how much fuel a little 1.3ltr rotary guzzles? They're not the cheapest daily.

Quick fun little machines, But have you had a look at the sort of money people are asking for them these days ?? If getting a rotary is a must then I would be going for an earlier RX7 . even the series 6 are not that expensive anymore. As for fuel economy an old friend I had used to own one. We are talking V8 like fuel consumption here.... Are you sure you want a Rotor as a daily ? They really are more of a weekend fun machine

Have owned a couple of RX-7's. They are thirsty (but frankly I couldn't care after owning several stroked V8's) plus all the other things that people generally associate with rotarys i.e. smooth, revvy etc.

I will say this though: a good, well maintained rotary is reliable. Poorly maintained or owned by someone who is not an enthusiast will result in a short engine life, more so than a piston powered car. For instance treat a rotary like a VN and boy oh boy is it not going to last long.

However that said between all of the rebuilds I have done rebuilding a rotary was the cheapest (compared to just about all the piston engines I have had aanyway) and for that rebuild I paid someone to do it (not having dealt with rotaries before).

I love them its just a love hate relationship and sometimes the hate wins out.

my old s4 rx7 averaged about 22o-250k to a 60lt tank not the most frugal thing as a dailey driver.

woah, hahah that thirsty. still be worth it, i won't it to be reliable as a daily driver but not primarily as one.

any of the rx series are shit hot

9yrs ago i used to own a ser2 rx7 running a ser4 13bt. Bought it for $5500, sold for $4500. wasnt a bunky by any means. Price 2day for them has skyrocketed as there getting harder to come by. wish i had kept it.

Awesome lightweight and addictive to drive machine. with 209rwhp (stock turbo @ 12psi, 3" TBE, old school wolf 2d) i ran a best of 13.9 @ 173km/hr (note traction was a problem but good top end). Reliable if properly setup and VERY easy to work on. Definetly weekend only car IMHO. rebuilds are cheap/easy as pointed out above. My advice would be a later model car for a daily as pointed out above.

check out www.perthrotary.com

The cars themselves are fine, reality is there a typical old capella or 808. Ususal old car stuff to worry about like rust and wear and tear, wouldnt be a problem on a good one if you spent the coin on it.. Theft and parts availability is the real drama, have a look what front and rear rx-3 parts sell for on ebay.

I drove my mates b1600 around for 6 months, made 400+hp at the tyres with a later model 13b, dowelled big throttle body, microtech and a tv51 truck turbo, the thing turned tyres in top gear as it came on boost and kept turning them past 200kph, it had a 80 Litre tank and used to average around 450km's to tank, that said we rebuilt it 3 times in a 2 year period and it probably got such great economy cause it was just to fast on the street...

Edited by NA_R33

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...