Jump to content
SAU Community

Recommended Posts

This problems only been starting since i've relocated my amp for my splits to under the drivers seat.

Anyway, I start the car up, drive off, no worries no interference or whine through the speakers what so ever. Pull over, stop, turn the car off, go do whatever, come back say 10 minutes later and crank some tunes and theres now whine in the speakers.

Start the car a few hours later and the whine has since left.

Can anyone see a reason for why this problem only occurs when the car has been running, stopped and then started again???

Thanks

Tim

Link to comment
https://www.sau.com.au/forums/topic/26994-that-dreaded-speaker-whine/
Share on other sites

The whine is actually electrical interfierance being induced into your RCA cable. Move all of your RCA cables far away from any power cables.

Next step is too triple check all earths including the one from the head unit and all amps to ground and from the battery to the bodywork. Make sure they are clean and the paint is rubbed back where they bolt to the bodywork. Make sure they are screwed in tight also check that the insulation on the signal cables isn't worn / cracked / damaged. :rofl:

Have you checked your flux capacitors? or perhaps the warp power relays? .................. Sorry about that! My missus had the same problem in her lancer and it ended up being the amp itself.I moved it back to the original position and it made no difference. i then used the amp on low pass for the sub and the noise was gone, seems to be a filtering problem in the amp. try another amp

Well your fronts need a high pass so they play treble only and your sub/s need low pass for bass only, so if you are running seperate amps and they are hi/lo pass selectable try swapping them to see if the problem goes away. The amps are probably different power ratings but it is just a test so lower your gains. another problem can be that your gains on your amps are too high, you should set your gains as low as poss and your head unit volume to about 90%, as a rule of thumb. I know it can be time consuming but most car audio development is.If you just lower the frequency then you will miss out on high notes and it will sound dull. good luck

yea the fronts hav a high pass on them.

I run jaycar 6.5 inch carbon fibre woofers with JVC cross overs and tweeters on the dash. The amp i use for the splits is a Pioneer 4x50wrms amp (coupla models old now) but still does hte job well.

Gains are set at just on half and the frequency is set on high pass @ 70hertz or there abouts.

I could run the gains higher because im not pushin the limits of the woofers what so ever and they're very efficient.

Is it worth trying another amp to see if its a problem there?

My amps located under the front seat if anyones had any problems there before

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Wheel alignment immediately. Not "when I get around to it". And further to what Duncan said - you cannot just put camber arms on and shorten them. You will introduce bump steer far in excess of what the car had with stock arms. You need adjustable tension arms and they need to be shortened also. The simplest approach is to shorten them the same % as the stock ones. This will not be correct or optimal, but it will be better than any other guess. The correct way to set the lengths of both arms is to use a properly built/set up bump steer gauge and trial and error the adjustments until you hit the camber you need and want and have minimum bump steer in the range of motion that the wheel is expected to travel. And what Duncan said about toe is also very true. And you cannot change the camber arm without also affecting toe. So when you have adjustable arms on the back of a Skyline, the car either needs to go to a talented wheel aligner (not your local tyre shop dropout), or you need to be able to do this stuff yourself at home. Guess which approach I have taken? I have built my own gear for camber, toe and bump steer measurement and I do all this on the flattest bit of concrete I have, with some shims under the tyres on one side to level the car.
    • Thought I would get some advice from others on this situation.    Relevant info: R33 GTS25t Link G4x ECU Walbro 255LPH w/ OEM FP Relay (No relay mod) Scenario: I accidentally messed up my old AVS S5 (rev.1) at the start of the year and the cars been immobilised. Also the siren BBU has completely failed; so I decided to upgrade it.  I got a newer AVS S5 (rev.2?) installed on Friday. The guy removed the old one and its immobilisers. Tried to start it; the car cranks but doesnt start.  The new one was installed and all the alarm functions seem to be working as they should; still wouldn't start Went to bed; got up on Friday morning and decided to have a look into the no start problem. Found the car completely dead.  Charged the battery; plugged it back in and found the brake lights were stuck on.  Unplugging the brake pedal switch the lights turn off. Plug it back in and theyre stuck on again. I tested the switch (continuity test and resistance); all looks good (0-1kohm).  On talking to AVS; found its because of the rubber stopper on the brake pedal; sure enough the middle of it is missing so have ordered a new one. One of those wear items; which was confusing what was going on However when I try unplugging the STOP Light fuses (under the dash and under the hood) the brake light still stays on. Should those fuses not cut the brake light circuit?  I then checked the ECU; FP Speed Error.  Testing the pump again; I can hear the relay clicking every time I switch it to ON. I unplugged the pump and put the multimeter across the plug. No continuity; im seeing 0.6V (ECU signal?) and when it switches the relay I think its like 20mA or 200mA). Not seeing 12.4V / 7-9A. As far as I know; the Fuel Pump was wired through one of the immobiliser relays on the old alarm.  He pulled some thick gauged harness out with the old alarm wiring; which looks to me like it was to bridge connections into the immobilisers? Before it got immobilised it was running just fine.  Im at a loss to why the FP is getting no voltage; I thought maybe the FP was faulty (even though I havent even done 50km on the new pump) but no voltage at the harness plug.  Questions: Could it be he didnt reconnect the fuel pump when testing it after the old alarm removal (before installing the new alarm)?  Is this a case of bridging to the brake lights instead of the fuel pump circuit? It's a bit beyond me as I dont do a lot with electrical; so have tried my best to diagnose what I think seems to make sense.  Seeking advice if theres for sure an issue with the alarm install to get him back here; or if I do infact, need an auto electrician to diagnose it. 
    • Then, shorten them by 1cm, drop the car back down and have a visual look (or even better, use a spirit level across the wheel to see if you have less camber than before. You still want something like 1.5 for road use. Alternatively, if you have adjustable rear ride height (I assume you do if you have extreme camber wear), raise the suspension back to standard height until you can get it all aligned properly. Finally, keep in mind that wear on the inside of the tyre can be for incorrect toe, not just camber
    • I know I have to get a wheel alignment but until then I just need to bring the rear tyres in a bit they're wearing to the belt on the inside and brand new on the outside edge. I did shorten the arms a bit but got it wrong now after a few klms the Slip and VDC lights come on. I'd just like to get it to a point where I can drive for another week or two before getting an alignment. I've had to pay a lot of other stuff recently so doing it myself is my only option 
    • You just need a wheel alignment after, so just set them to the same as current and drive to the shop. As there are 2 upper links it may also be worth adding adjustable upper front links at the same time; these reduce bump steer when you move the camber (note that setting those correctly takes a lot longer as you have to recheck the camber at each length of the toe arm, through a range of movement, so you could just ignore that unless the handling becomes unpredictable)
×
×
  • Create New...