Jump to content
SAU Community

Recommended Posts

This problems only been starting since i've relocated my amp for my splits to under the drivers seat.

Anyway, I start the car up, drive off, no worries no interference or whine through the speakers what so ever. Pull over, stop, turn the car off, go do whatever, come back say 10 minutes later and crank some tunes and theres now whine in the speakers.

Start the car a few hours later and the whine has since left.

Can anyone see a reason for why this problem only occurs when the car has been running, stopped and then started again???

Thanks

Tim

Link to comment
https://www.sau.com.au/forums/topic/26994-that-dreaded-speaker-whine/
Share on other sites

The whine is actually electrical interfierance being induced into your RCA cable. Move all of your RCA cables far away from any power cables.

Next step is too triple check all earths including the one from the head unit and all amps to ground and from the battery to the bodywork. Make sure they are clean and the paint is rubbed back where they bolt to the bodywork. Make sure they are screwed in tight also check that the insulation on the signal cables isn't worn / cracked / damaged. :rofl:

Have you checked your flux capacitors? or perhaps the warp power relays? .................. Sorry about that! My missus had the same problem in her lancer and it ended up being the amp itself.I moved it back to the original position and it made no difference. i then used the amp on low pass for the sub and the noise was gone, seems to be a filtering problem in the amp. try another amp

Well your fronts need a high pass so they play treble only and your sub/s need low pass for bass only, so if you are running seperate amps and they are hi/lo pass selectable try swapping them to see if the problem goes away. The amps are probably different power ratings but it is just a test so lower your gains. another problem can be that your gains on your amps are too high, you should set your gains as low as poss and your head unit volume to about 90%, as a rule of thumb. I know it can be time consuming but most car audio development is.If you just lower the frequency then you will miss out on high notes and it will sound dull. good luck

yea the fronts hav a high pass on them.

I run jaycar 6.5 inch carbon fibre woofers with JVC cross overs and tweeters on the dash. The amp i use for the splits is a Pioneer 4x50wrms amp (coupla models old now) but still does hte job well.

Gains are set at just on half and the frequency is set on high pass @ 70hertz or there abouts.

I could run the gains higher because im not pushin the limits of the woofers what so ever and they're very efficient.

Is it worth trying another amp to see if its a problem there?

My amps located under the front seat if anyones had any problems there before

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Ok i will get those 310mm. I found one but on a different site. This is the description on those...is it ok? Technical parameters: - Axle: front. - Disc type: ventilated. - Number of holes: 5. - Disc diameter: 310mm. - Total height with center: 54mm. - Thickness (new/min.): 30/28mm. - Designed for brake calipers manufacturer: Sumitomo.
    • You Gregged a whole racetrack!?
    • Look for broken wire or bad connector at the motor. Might not be it, but is worth starting there, as it is easy.
    • Hi everyone, I’m having an issue with my R32 GT-R. Sometimes, when the car goes over a bump or experiences some vibration, the 4WD warning light comes on the dashboard. When I check the code from the control unit in the trunk, it shows Code 19 – ETS Motor. However, everything seems to be working fine — if I turn off the engine and restart the car, the light goes away and everything functions normally. Has anyone experienced this before? Where should I start troubleshooting this issue? Thanks in advance!
    • I'm back from the dyno - again! I went looking for someone who knew LS's and had a roller dyno, to see how it shaped up compared to everything else and confirm the powerband really is peaking where Mr Mamo says it should. TLDR: The dyno result I got this time definitely had the shape of how it feels on the road and finally 'makes sense'. Also we had a bit more time to play with timing on the dyno, it turns out the common practice in LS is to lower the timing around peak torque and restore it to max after. So given a car was on the dyno and mostly dialled in already, it was time for tweaking. Luis at APS is definitely knowledgable when it came to this and had overlays ready to go and was happy to share. If you map out your cylinder airmass you start seeing graphs that look a LOT like the engine's torque curve. The good thing also is if you map out your timing curve when you're avoiding knock... this curve very much looks like the inverse of the airmass curve. The result? Well it's another 10.7kw/14hp kw from where I drove it in at. Pretty much everywhere, too. As to how much this car actually makes in Hub Dyno numbers, American Dyno numbers, or Mainline dyno numbers, I say I don't know and it's gone up ~25kw since I started tinkering lol. It IS interesting how the shorter ratio gears I have aren't scaled right on this dyno - 6840RPM is 199KMH, not 175KMH. I have also seen other printouts here with cars with less mods at much higher "kmh" for their RPM due Commodores having 3.45's or longer (!) rear diff ratios maxing out 4th gear which is the 1:1 gear on the T56. Does this matter? No, not really. The real answer is go to the strip and see what it traps, but: I guess I should have gone last Sunday...
×
×
  • Create New...