Jump to content
SAU Community

Steam Cleaning An Engine

[200]

By [200],
in General Automotive Discussion

 Share

Recommended Posts

W0rp3D Grand Master

W0rp3D

Posted
Posted

I am looking at steam cleaning an engine thats been removed from a car. It's dirty as all hell, lots of shit built up on it ect...

Looking at getting a steam cleaner to get it nice and clean again.

Can anyone suggest one for me?

a few $2 cans of degreaser and a hose should get it, if its really really bad try scraping some of the bigger chunks off first.

SECURITY Grand Master

SECURITY

Posted
Posted

there are better degreasers than that $2 shit you get from supercheap - thats just the stuff that will get you out of trouble in your usual day to day.

there are heavy duty automotive degreasers you can get but you've got to wear gloved while using it - just look harder.

syfon Veteran

syfon

Posted
Posted
i used a high pressure washer that could get the water to 200degrees that works really well, you should be able to hire them but there quite big

LOL heats the water to 200degrees? if it was to be heated to 200degrees within this machine, it would be under an incredible amount of pressure....i mean if it exploded it would cause some serious damage to you!

and as soon as the "water" comes out from the nozzle it would almost instantly turno to steam.

So what i think you meant to say is that it hears the steam to 200degrees under an enormous amount of pressure.....

Lol i thought i would just add my 2cents worth :ninja:

Birds Grand Master

Birds

Posted
Posted
LOL heats the water to 200degrees? if it was to be heated to 200degrees within this machine, it would be under an incredible amount of pressure....i mean if it exploded it would cause some serious damage to you!

and as soon as the "water" comes out from the nozzle it would almost instantly turno to steam.

So what i think you meant to say is that it hears the steam to 200degrees under an enormous amount of pressure.....

Lol i thought i would just add my 2cents worth :nyaanyaa:

Hence the term "steam cleaning"? I've seen these machines, they are fantastic when used with a good caustic degreaser. Bout the size of a small go kart. And yes, they are under a large amount of pressure.

NZM.031 Grand Master

NZM.031

Posted
Posted

steam cleaners are great if you can get one, degreasers are shit as they leave a horrible residue, but you could use cheap degreaser to get most of it clean, then something like brake cleaner as it doesnt leave a residue, Kenco Shift it is awesome too... or spray and wipe.... spray it on, leave it soak in for a bit, then hose it off.

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      Rear subframe stay bracket bolt removal issues

      By MBS206 · Posted

      I normally run with I think a 10mm, and definitely use the second handle you can add to a drill. They hurt when they bins up!   For the crush tube, once all subframe is clear, I'd try some stilsons and see if I can get it to start to twist.
    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      Probably because they couldn't, because the use of the variable resistor to create a "signal" in the ECU is managed by the ECU's circuitry. The only way that VDO could do it would be if they made a "smart" sensor that directly created the 0-5V signal itself. And that takes us back to the beginning. Well, in that case, you could do the crude digital (ie, binary, on or off) input that I mentioned before, to at least put a marker on the trace. If you pressed the button only at a series of known integer temperatures, say every 2°C from the start of your range of interest up to whatever you can manage, and you know what temperature the first press was at, then you'd have the voltage marked for all of those temperatures. And you can have more than one shot at it too. You can set the car up to get the oil hot (bypass oil coolers, mask off the air flow to oil coolers, and/or the radiator, to get the whole engine a bit hotter, then give it a bit of curry to get some measurements up near the top of the range.   On the subject of the formula for the data you provided, I did something different to Matt's approach, and got a slightly different linear formula, being Temp = -22.45*V + 118.32. Just a curve fit from Excel using all the points, instead of just throwing it through 2 points. A little more accurate, but not drastically different. Rsquared is only 0.9955 though, which is good but not great. If you could use higher order polynomials in the thingo, then a quadratic fit gives an excellent Rsquared of 0.9994. Temp = 2.1059*V^2 - 34.13*V + 133.27. The funny thing is, though, that I'd probably trust the linear fit more for extrapolation beyond the provided data. The quadratic might get a bit squirrely. Hang on, I'll use the formulae to extend the plots.... It's really big so you can see all the lines. I might have to say that I think I really still prefer the quadratic fit. It looks like the linear fit overstates the temperature in the middle of the input range, and would pretty solidly understate what the likely shape of the real curve would say at both ends.
    • Kinkstaah
      [HOW-TO] Winter Steam-Clean & Odour Removal in 30 min

      By Kinkstaah · Posted

      I got a hand held bisssel one and it's a piece of shit. Doesn't work for more than about 5 seconds. So much so that I nearly refuse to believe any wet dry vac actually works or has enough suction to clean the carpet of a car. I'm discouraged as all the good ones are $300+ for an unknown result. I saw MCM did a Ryobi video where they use this thing: https://www.ryobi.com.au/products/stick-vacuum-cleaners/18v-one-hptm-brushless-spot-cleaner-tool-only Anyone have any experience actually using a tool like this when not paid to showcase it?
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      That could very well be the thermistor, but the ECU only sees Volts. VDO don't seem to provide a 0-5 volt curve, only the resistance curve.... (or line).
    • GTSBoy
      Rear subframe stay bracket bolt removal issues

      By GTSBoy · Posted

      Yes. Probably, given that there is only access from the bottom end of it, go with a drill bit. Don't start too small. 7 or 8mm is probably the right size. You want something that can make a big enough hole to do some damage, but not so bit that it clashes with the steel or binds up and breaks your wrist. A slow speed is probably a good idea too. Once the rubber is destroyed, you then have to get the crush tube off the stud, which will be the whole heat/oil/cutting exercise all over again, but this time with the need to strictly avoid damaging the stud (any further than the corrosion might already have done.
×
×
  • Create New...