Jump to content
SAU Community

Drag Racing Ring In Northern Suburbs Smashed

Taso84

By Taso84,
in Victoria

 Share

Recommended Posts

  • Replies 141
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

Rav Proficient

Rav

Posted
Posted

If people get negative about all this burnout stuff in the northern suburbs, They need to understand where else can you go these day's. They shut down Calder park because of health and safety. The government need to get more involved with car event's and the venues they hold them at. I am sure Bob Jane has closed Calder until November because of funds, I bet if he had more support it would open up faster. Myself goes to a lot of car events and to this illegal drags because that's all there is at the moment, plus it is great to watch the crowd get excited when some one pop's there tyres. So if the goverment doesnt help out where else do they expect people to go, Look at drifting here in australia they need more support aswell.

But they dont say this point's in the paper or on the new's they just show people who say dumb things.

SO GET OUT THERE AND SUPPORT YOUR LOCAL CAR CLUB.

MattD Proficient

MattD

Posted
Posted
If people get negative about all this burnout stuff in the northern suburbs, They need to understand where else can you go these day's. They shut down Calder park because of health and safety. The government need to get more involved with car event's and the venues they hold them at. I am sure Bob Jane has closed Calder until November because of funds, I bet if he had more support it would open up faster. Myself goes to a lot of car events and to this illegal drags because that's all there is at the moment, plus it is great to watch the crowd get excited when some one pop's there tyres. So if the goverment doesnt help out where else do they expect people to go, Look at drifting here in australia they need more support aswell.

But they dont say this point's in the paper or on the new's they just show people who say dumb things.

SO GET OUT THERE AND SUPPORT YOUR LOCAL CAR CLUB.

You are beating the dead horse, mate.

However, vis a vis attending these events? Well, you're apparent civil disobedience not withstanding, they are dangerous and illegal for a reason.

When life gives you lemons, you make lemonade. You don't stick your cock in the glass and call it lemonade.

abacusnow Enthusiast

abacusnow

Posted
Posted

"SO GET OUT THERE AND SUPPORT YOUR LOCAL CAR CLUB."

How is a group of dickheads breaking dozens of laws and endangering lives a 'car club'? Its that type of 'theres no where else' attitude that leads to these problems. There are plenty of places. Talk to your Council. I live in Ballarat, and we have an airport that is reasonable and open to allowing people access to isolated parts of their land and runway. There is the Ballarat Light Car Club, which is incredibly cheap and has an autocross track, and which participates in hillclimb events and track days. etc.

no where else my freeking ass.

Guest
This topic is now closed to further replies.
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      boost source Size Garrett gt28 gen2

      By GTSBoy · Posted

      Totally equivalent. Stock often goes from the comp cover because that's where the actuator is also installed and the factory needs 2" of hose to make the connection - and it comes as a pre-assembled unit. They totally have a boost reference from somewhere between the turbo and the throttle(s). Oh, jeez. Just do it in M12 then. We don't actually care that much. I would expect any such AN converter fitting to rely on an o-ring or some other seal onto a flat surface under the flange of the hex**, because bolt threads are no intended to provide a pressure seal. unlike..... pipe threads. **which also requires a suitably flat and smooth surface on the turbo's boss to provide the seal.
    • timmy94
      boost source Size Garrett gt28 gen2

      By timmy94 · Posted

      I also used NP   That’s were it’s seems to be the best place to fit it? All schematic shows also that it’s should be referenced from the turbo housing. But idk, I do see high hp cars without any connection or anything to their turbos, so I really don’t know how they connect their things
    • timmy94
      boost source Size Garrett gt28 gen2

      By timmy94 · Posted

      I do have loctite 243 and 246 and a few more models. I could drill it now in place and make new threads for m12 and order an4 - m12 coupling and fit that to the turbo. Run a braided hose to the EBC which I could get a an4 to 1/8npt 
    • timmy94
      boost source Size Garrett gt28 gen2

      By timmy94 · Posted

      So M12 and sealant should be fine?    NPT ” because that’s what I had and what I could get atm. 
    • r32-25t
      R32 gtr transmission strength, billet plate

      By r32-25t · Posted

      Wouldn’t touch par if they gave it to me. You need to ask how much power you’re looking to make and then add about 50% to it because that’s what you’ll end up making  The factory box says no more at about 350kw or so, the upgraded synchro boxes won’t handle much over 500kw for long and at that point you’re looking at an auto or dog engagement manual,  once you’ve gone dog engagement you may as well go sequential, they cost a little bit more but it’s worth it  also while you’re at it you should upgrade the transfer case with 10 friction plates 
×
×
  • Create New...