Jump to content
SAU Community

Recommended Posts

Hey all,

My r33 gtst is putting out about 210kw with a selection of basic bolt on goodies. My goal isn't to make big numbers but I do want usable power. So having said that here is my issue.

As it seems at the moment 1st pulls quite well but shifting up into any gear even from redline has some serious lag. I don't appear to get any power back for 2-3 seconds in the next gear but then it kicks. This doesn't feel like a fuel supply issue nor does it miss or splutter (but i will be putting something like a 040 in soon anyway). (injectors are getting high on there duty cycle but certainly not maxing). Spark plugs are also new gapped at .8 (coppers)

So this is what the car has.

3" inch turbo back stainless steal exhaust with hiflow cat

apexi pod filter

turbo smart bleed valve (peaking at 12psi)

blitz front mount (this is no doubt not helping the lag issue at my current power)

apexi powerfc (tuned by re customs)

adjustable exhaust gear (currently at 0 degrees)

I'm assuming having just a bleed valve it may be allowing the wastegate to be opening early. But would it be that bad that an ebc would make all the difference? i don't know but i am assuming not.

I will also be looking at getting the standard turbo hi flowed mainly so the 13yo turbo doesn't disintegrate into my engine...but will the hi flow allow a faster spool up or should I be looking to spend more cash on gt-rs or similar? (a bolt on option is much more preferable than having to get custom piping / manifold made)

The car hasn't been tuned since we did the 100,000k service to it (and this is when the adjustable cam gear went on) So not sure if much if any benefit will come out of that at this stage.

anyway just looking for suggestions on what road i should be going down. I don't have a large wallet and i reiterate im not after big power figures just for the power to come on more linear.

Cheers

Camden

Link to comment
https://www.sau.com.au/forums/topic/271825-getting-rid-of-that-flat-spot/
Share on other sites

is your blow off valve set up and working properly. and also is the injector time delay set up properly ? cant remember propper word for it but it is why subarus feel laggy when you put a front mount on them . maf sees more air so puts in more fuel . extra air hasnt reached motor yet but xtra fuel has so rich flat spot then clears .

what is your boost gauge doing right after a shift ?

is your blow off valve set up and working properly. and also is the injector time delay set up properly ? cant remember propper word for it but it is why subarus feel laggy when you put a front mount on them . maf sees more air so puts in more fuel . extra air hasnt reached motor yet but xtra fuel has so rich flat spot then clears .

what is your boost gauge doing right after a shift ?

The blow off valve is standard and plumped back as it should be (and appears to be functioning correctly)

As for injector delay I am not sure but would be hoping this should be looked after correctly by my tuner (of whom i trust) although the car does run quite rich as demonstrated all over my rear bar.

I cant tell you exactly about how the boost gauge responds atm as im out of town (back home in a week) but from memory on shift and peddle down it jumps straight back up to something just over 0... maybe about 5psi!? sits there for that few seconds then builds its way to 12 relatively quickly. (like i said will be able to explain better next week when get home and give it a drive)

Cheers

Camden

not going to doubt Ray as i know they do great work, but maybe talk to him about retarding the exhaust cam gear 2degrees(suggesting from other threads i have read, it is meant to help response) and pre boost timing, might be able to run more?

I've never heard lag and standard turbo said in the same post...

If the bov is working properly, then maybe you have an ignition problem...

Another thing, that has happened in the past, is the adjustable cam gear on tight?

If the bov is working properly, then maybe you have an ignition problem...

There is no obvious missing and when i changed the plugs and at that time i looked to see if there was any arching happening with the coil packs before putting the garnish back on and everything seems alright.

Another thing, that has happened in the past, is the adjustable cam gear on tight?

cam gear is torque to what was specified on the paperwork but its not something that happened after putting it on anyway... was like this before.

Cheers

Camden

not going to doubt Ray as i know they do great work, but maybe talk to him about retarding the exhaust cam gear 2degrees(suggesting from other threads i have read, it is meant to help response) and pre boost timing, might be able to run more?

Yeah I'll definitely talk to Ray about it when i get back to Melb and get him to do a bit of a retune. Maybe go down the ebc path to at the same time and see what he can do with it.

This really has been something that the car has been doing for a long time but was less obvious up until recently as my clutch was progressively dieing. I now have a much more serious clutch (certainly no slippage anymore).

Cheers

Camden

its possibly your boost controller. if it doesnt allow the wastegate to close quickly enough, this will happen.

i had a similar thing happening with my turbotech mbc. then i drilled a hole into it to let the pressure out of the actuator line immediately, and it made a huge difference.

theres always going to be the split second re-spool at gear changes. but 2 or 3 seconds is too long.

Turbo smart bleed valve has a TPiece in it correct?

If it does, openit, remove the ball and spring, put it back together. (WITHOUT THE BALL AND SPRING)

This thing holds the waste gate open.

Had the same Boost Controller, had the EXACT same issue.

Turbo smart bleed valve has a TPiece in it correct?

If it does, openit, remove the ball and spring, put it back together. (WITHOUT THE BALL AND SPRING)

This thing holds the waste gate open.

Had the same Boost Controller, had the EXACT same issue.

Certainly worth trying! I never thought of removing it as i was under the impression you only removed it if your boost was spiking.

Cheers

Camden

Certainly worth trying! I never thought of removing it as i was under the impression you only removed it if your boost was spiking.

Cheers

Camden

Typically you remove the whole boost controller as it is a bastard piece of shit really. (Although mine is still bolted to the firewall, it really is crap, and is disconnected)

Typically you remove the whole boost controller as it is a bastard piece of shit really. (Although mine is still bolted to the firewall, it really is crap, and is disconnected)

Your post doesn't really make any sense... Are you just trying to make the point that an ebc is better than a bleed valve (clearly this is true so not very helpful)

Or do you think we are talking about the stock boost solenoid?!? the stock solenoid is redundant with the bleed valve or an ebc for that matter and is bypassed...

Cheers

Camden

i had a worse version of this issue when i had a turbosmart dual stage controller. i would change gear and not get any boost until i lifted off again for a little bit. first time i changed into 3rd with the controller on i was at about 4000rpm (had just changed from 2nd at high rpm) and had zero boost with WOT.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...