Jump to content
SAU Community

Recommended Posts

what are legal positions for front number plate? after getting my car resprayed i want to mount front number plate on the side but dont know which side?

i already had cops trying to defect me for number plate angle and only 2 screws coz they couldnt find anything else, so i wanna be sure before i drill any holes in freshly sprayed front bar.

Link to comment
https://www.sau.com.au/forums/topic/272186-number-plate-position/
Share on other sites

i dunno whats legal but i have mine mounted on the left and ive had many cops look at my car and not say anything about it :rofl:

i think its got to be about 100mm off the ground to be legal or something , might have to call regency up mate

passenger side. only reason i chose that side is a lot of cars that come from the factory with offset plates, have em on that side (ie alpha romeo).

dont think they are to fussed on which side they are on. but it would make sense to have them on the drives side though, that way on-coming traffic can see it with ease

OK..

i was pulled up by a cop at a car park on one of kell's cruises,

i had it on the passenger side, right down the bottom of the bar.

she didnt mind it being on the side, or on an angle, but said it had to be ATLEAST 30cm off the ground.

first hand info right there.

I'm not sure about the ruling in SA, but in Vic it must be legible when viewed from a 45-degree angle from either side of the car.

Its about 20 degrees maximum in the official transport SA guidelines but like craig said, they're more concerned about visibility and height - I've never had any issues with my plate, it went thru regency fine with the relocation kit and that has around a 10 degree angle

-D

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
×
×
  • Create New...