Jump to content
SAU Community

Recommended Posts

jus spent the last hour on search trying to figure this out and this wat i make of it....pleases correct me if im wrong....

there are 4 cradle bushes which need cradle to b dropped and bushes pressed in/out. alot of work and labour.

u can buy solid alloy bush cradle inserts x 8 which stiffen rear up but sum say gets noisy sum say not. cradle stays on

then theres pineapples x4 which depending on how its mounted promotes traction/grip or drift. cradle stays on.

how do u know which option to go for and wat u need. im after grip, reduce tramping and general upgrade of worn bushes. i found a nice basic diagram showing where pineapples go for different results.

sorry for being 'slow' but jus after a simple breakdown of the whole thing.

then also u can get rear diff bushes x4.

thanx

Link to comment
https://www.sau.com.au/forums/topic/272740-info-on-rear-cradle-bushes-r32-gtst/
Share on other sites

get the alloy ones i did im im very happy for it

the noise factor is so small ill bet 5 that you probably will never notice it mate

but you will notice the car is heaps better to drive

did u replace the inner bushes, or just the subframe-chassis bushes? the real NVM comes from when u solid mount the inner bushes as well, which a lot of people dont.

for a daily i would stick with Urethane, especially if ur running a lot of rubber around the place and softish suspension. there are usually other causes to the axle tramp before ur subframe bushes.

What do you mean by "worn"? The rear subframe bushes are silicone filled, they need replacing when they burst and the silicone starts dripping out. If there is no silicone leak then they don't need replacing. In which case pineapples are the go as you can change the rear subframe angle, something R32's really need.

Cheers

Gary

did u replace the inner bushes, or just the subframe-chassis bushes? the real NVM comes from when u solid mount the inner bushes as well, which a lot of people dont.

for a daily i would stick with Urethane, especially if ur running a lot of rubber around the place and softish suspension. there are usually other causes to the axle tramp before ur subframe bushes.

i solid mounted the lot and im very happy

including solid uretane for the diff which means you ca hear the diff but its unrelated

come and have a drive of mine if your local and see for your self

i solid mounted the lot and im very happy

including solid uretane for the diff which means you ca hear the diff but its unrelated

come and have a drive of mine if your local and see for your self

isnt the diff solid anyway? lol

may be different on GTR's, i know R32 GTS-t's are solid, R33 GTS-t's have a bush on the front mount.

i dont care a great deal about NVM so its not something i look a lot into lol

when i got the car it was pretty much bone stock as well, but it had been converted to a manual, and a fairly budget job as well, maybe they came out when they did the conversion :S

i run some urethane bushes i made up with my R33 diff at the front mounts as it needs to be spaced down, but nothing for the 32 diff.

so the cradle bushes only need changing if they leak... ok ... mine arnt leaking so that answers that question

next is the difference between the cradle inserts and pineapples. which one applies when ?? thanx for all the replies....

u have bushes IN the subframe, where the bolts go through which holds the subframe to the chassis, then u have bushes that sit between the subframe and the chassis. the ones that sit in between the subframe and chassis "align" ur subframe, so u can change the tilt, which changes the amount of squat u get.

The cradle bushes near the doors are silicone filled, if they're stuffed its fairly obvious, the rear ones are solid rubber. When I replace my cradle bushes the front were stuffed but the rears were still ok, no tears in the rubber and looked good. It is harder to tell if the rears are gone. I replaced all four and even though only the fronts were stuffed it was noticeable under hard acceleration out of corners that there was a positive difference. Didn't notice it at all when driving normally though. If the cars a long term proposition then I would do the cradle bushes if not then you would probably get away with the pineapples.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
    • In my head it does make sense to be a fuel problem since that is what I touched when cleaning the system. When I was testing with the fuel pressure gauge, the pressure was constantly 2.5 bar with the FPR vacuum removed. When stalling, the pressure was going up to 3.0 bar (which is how it should be on ignition).
    • ECUtalk pages don't mention they support the ABS computer (consult port has more than one CAN), so you might just need a different scan tool. But, I would expect ABS is a different light to the brake warning/handbrake light, do you see an ABS light come on for a few seconds when you turn the key from ACC to IGN? But since you said: I'd have a look at the ABS sensors in the rear hubs to make sure they are not damaged, disconnected etc.
×
×
  • Create New...