Jump to content
SAU Community

Recommended Posts

Hi people. Well the slide hi-flow is now out and it is now time for the 3076 to go in. In regards to the studs in the standard manifold is the best thing to get them out with is some CRC and vice grips? Also should i change the standard manifold or will this be adequate. Finally the water line that goes from the turbo to the rear of the engine, how do you get this sucker off? Any help would be appreciated. Thank's :thumbsup:

Link to comment
https://www.sau.com.au/forums/topic/273729-pre-turbo-install/
Share on other sites

Studs - you are more than likely to break a couple mate. CRC them a few times during the day and leave overnight to give you the best chance at getting them all out

Stock manifold is fine

And water line - with a bit of elbow grease, again perhaps CRC overnight.

The fun continues as i have now removed the manifold because i noticed four were broken. Is it fairly easy to take the broken one's out with the right tool's or should i call in someone. In regards to spacer plate and oil lines the turbo will be coming in full bolt on kit form (spacer plate, oil and water lines nuts, studs, gaskets etc).

IMO get rid of the waterlines, i dont see a point for them, when there's hot water running through them all the time.

As for where it ends up is behind the intake manifold, undo the 2 bolts on the head, if the hose doesnt come off you can always chop a bit hoes off, rust normally cramps it and its hard to remove.

What do you mean you dont see a point for the waterlines...? The turbo is water cooled!!!

As for the broken studs - call someone in. Its not that expensive and there are mobile guys in each state :)

Try get your others out first though, likely more will crack.

Thank's for all your imput guys. As far as the bolt for the water line behind the block do i have to really take the driver side rocket cover off. I have to admit though i've tried about five times now and cannot even get the spanner onto it.

Also make sure your oil lines are correct because using stock oil line is a no no. When i had my hypergear installed bymyself... i didnt get told to install a aftermarket oil line so therefore it blew up. So make sure u get an oil line.

That cleared my miss thoughts, ive been running an rb25 turbo without them for a while, guess it couldnt be good for the ceramic wheel.. :(

Id be more worried about the core.

A ball bearing turbo by nature requires less oil to lube the bearings. The offset to this less oil means there is less cooling going on.

Hence ball bearing turbos are ALL water cooled.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I drive the Tiguan much harder than the Skyline in all conditions, because it just grips and hooks, unlike the R33 shit box
    • The rain is the best time to push to the edge of the grip limit. Water lubrication reduces the consumption of rubber without reducing the fun. I take pleasure in driving around the outside of numpties in Audis, WRXs, BRZs, etc, because they get all worried in the wet. They warm up faster than the engine oil does.
    • When they're dead cold, and in the wet, they're not very fun. RE003 are alright, they do harden very quickly and turn into literally $50 Pace tyres.
    • Yeah, I thought that Reedy's video was quite good because he compared old and new (as in, well used and quite new) AD09s, with what is generally considered to be the fast Yokohama in this category (ie, sporty road/track tyres) and a tyre that people might be able to use to extend the comparo out into the space of more expensive European tyres, being the Cup 2. No-one would ever agree that the Cup 2 is a poor tyre - many would suggest that it is close to the very top of the category. And, for them all to come out so close to each other, and for the cheaper tyre in the test to do so well against the others, in some cases being even faster, shows that (good, non-linglong) tyres are reaching a plateau in terms of how good they can get, and they're all sitting on that same plateau. Anyway, on the AD08R, AD09, RS4 that I've had on the car in recent years, I've never had a problem in the cold and wet. SA gets down to 0-10°C in winter. Not so often, but it was only 4°C when I got in the car this morning. Once the tyres are warm (ie, after about 2km), you can start to lay into them. I've never aquaplaned or suffered serious off-corner understeer or anything like that in the wet, that I would not have expected to happen with a more normal tyre. I had some RE003s, and they were shit in the dry, shit in the wet, shit everywhere. I would rate the RS4 and AD0x as being more trustworthy in the wet, once the rubber is warm. Bridgestone should be ashamed of the RE003.
    • This is why I gave the disclaimer about how I drive in the wet which I feel is pretty important. I have heard people think RS4's are horrible in the rain, but I have this feeling they must be driving (or attempting to drive) anywhere close to the grip limit. I legitimately drive at the speed limit/below speed the limit 100% of the time in the rain. More than happy to just commute along at 50kmh behind a train of cars in 5th gear etc. I do agree with you with regards to the temp and the 'quality' of the tyre Dose. Most UHP tyres aren't even up to temperature on the road anyway, even when going mad initial D canyon carving. It would be interesting to see a not-up-to-temp UHP tyre compared against a mere... normal...HP tyre at these temperatures. I don't think you're (or me in this case) is actually picking up grip with an RS4/AD09 on the road relative to something like a RE003 because the RS4/AD09 is not up to temp and the RE003 is closer to it's optimal operating window.
×
×
  • Create New...