Jump to content
SAU Community

Recommended Posts

you mean an RD28?

I think it has been done. From what ive read the RD28 has a very long stroke for its bore size, so they arent the most free revving motors. In the end not really worth the expense and effort when you could jus stroke a 26, or build a 3.0L

Edited by MintR33
Link to comment
https://www.sau.com.au/forums/topic/275654-diesel-block/#findComment-4669316
Share on other sites

I believe the stroke is the same asa the rb30. It has been done by someone on here. From what i gather its a massive job with head bolts in different spots, water and oil galleries not lining up etc. Would be a good start if you want to make over 1200hp, otherwise its not really needed. I would speak to rips, as im sure they have looked down this alley to see if its worthwhile.

Link to comment
https://www.sau.com.au/forums/topic/275654-diesel-block/#findComment-4669654
Share on other sites

I've got an RD28 block here at the moment. The rear oil drain on one side is missing, it's slightly different timing wise at the front, set up with a high mount tensioner from the factory. The head bolt holes are in the same spots though and main tunnel sizes are the same as an RB30, it also has piston oil squirters and weighs a heap more than an RB30. It's very do-able and has been done in the past.

  • Thanks 1
Link to comment
https://www.sau.com.au/forums/topic/275654-diesel-block/#findComment-4680723
Share on other sites

how does the main cap/girdle setup look in them in comparison to the rb30? Pretty well the same? Oil pick up position?

Much the same as a 30, I can snap some photos if you like, I'm doing a little dummying up this w/e. Let me know what you want to see.

Link to comment
https://www.sau.com.au/forums/topic/275654-diesel-block/#findComment-4682297
Share on other sites

Is it really worth all the messing around?

i can see the interest of seeing if it matches up but really when an Rb30 block is ready to go i fail to see the point. looking at R.I.P.S engines and plenty of other Rb's i think the Rb30 is plenty enough capable of big HP.

How much HP are you chasing? I can't see why people seem to think this block will be so much stronger? after all the bores are in the same place and it fits the same head so there is not heaps of extra meat....

Edited by GT-RZ
Link to comment
https://www.sau.com.au/forums/topic/275654-diesel-block/#findComment-4685352
Share on other sites

Is it really worth all the messing around?

i can see the interest of seeing if it matches up but really when an Rb30 block is ready to go i fail to see the point. looking at R.I.P.S engines and plenty of other Rb's i think the Rb30 is plenty enough capable of big HP.

How much HP are you chasing?

When you are building a $250,000 Pro FX drag car it matters. You have to compete against rotors and 2J's making obscene amounts of power.

To run 60psi of boost and not change the engine after 3 runs (this is what Titan Motorsport in the states do with their 2J engines) needs a very rigid thick walled block...RD28 is the only option for the Nissan runners....for now anyway...something else is being looked at too. If it works it will be big.

Edited by DiRTgarage
Link to comment
https://www.sau.com.au/forums/topic/275654-diesel-block/#findComment-4686498
Share on other sites

Actually proengines, the whole block if you dont mind....im interested in what they look like in comparison. Having never seen one before. A picture of every face if thats not asking too much mate?

Im sure alot of others would be curious to see what they look like too for comparative sake.

I believe the bores are considerably thicker in these motors as others have already mentioned.

Link to comment
https://www.sau.com.au/forums/topic/275654-diesel-block/#findComment-4686608
Share on other sites

The bores could only be thicker on the sides of the block was my point as obviously the material between bores is constant with that of the other RB's (once bored out to 86mm)

but realistically i get what your saying as sleeving can take care of most the direct stresses in BIG HP within the cylinder and the next big problem would be twisting the block. which 40kg extra material around the sides may well fix. i have never seen one. although very interested now as 40kg is allot of extra cast iron, the block must look very fat indeed. how much does an RB30 block weigh? not too much i assume as they are not too hard to move around by hand.

my point was simply towards people in here who are thinking of doing this conversion and probably intending to run no where near 1000hp. For the serious drag monsters this could be an avenue worth the while but for streeters and circuit work i don't see the point. unless you have lots of extra time on your hands and want something to do!

lets just get a 2jz and stamp nissan on the top :laugh:

Or even better someone just machine up a fresh block and head from a solid billet block.

would be nice to get some images of the rd28 and also some measurements. because that's the only way to prove it is stronger.

Edited by GT-RZ
Link to comment
https://www.sau.com.au/forums/topic/275654-diesel-block/#findComment-4686997
Share on other sites

To run 60psi of boost and not change the engine after 3 runs (this is what Titan Motorsport in the states do with their 2J engines) needs a very rigid thick walled block...RD28 is the only option for the Nissan runners....for now anyway...something else is being looked at too. If it works it will be big.

tb48 with rb26 head...?

Link to comment
https://www.sau.com.au/forums/topic/275654-diesel-block/#findComment-4687160
Share on other sites

I think the TB48 all by itself is a better option without a different head... i think you can stroke them to 5litres too??? i just never thought about one of them in lil ol silvia. big engines.

dammit. i have two rb30's here and now i want a Tb48!!!!! lol.

post-41232-1246332214_thumb.jpg

seems there is support for them too http://www.briancrower.com/makes/nissan/tb48.shtml

Link to comment
https://www.sau.com.au/forums/topic/275654-diesel-block/#findComment-4687202
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Next on the to-do list was an oil and filter change. Nothing exciting to add here except the oil filter is in a really stupid place (facing the engine mount/subframe/steering rack). GReddy do a relocation kit which puts it towards the gearbox, I would have preferred towards the front but there's obviously a lot more stuff there. Something I'll have to look at for the next service perhaps. First time using Valvoline oil, although I can't see it being any different to most other brands Nice... The oil filter location... At least the subframe wont rust any time soon I picked up a genuine fuel filter, this is part of the fuel pump assembly inside the fuel tank. Access can be found underneath the rear seat, you'll see this triangular cover Remove the 3x plastic 10mm nuts and lift the cover up, pushing the rubber grommet through The yellow fuel line clips push out in opposite directions, remove these completely. The two moulded fuel lines can now pull upwards to disconnect, along with the wire electrical plug. There's 8x 8mm bolts that secure the black retaining ring. The fuel pump assembly is now ready to lift out. Be mindful of the fuel hose on the side, the hose clamp on mine was catching the hose preventing it from lifting up The fuel pump/filter has an upper and lower section held on by 4 pressure clips. These did take a little bit of force, it sounded like the plastic tabs were going to break but they didn't (don't worry!) The lower section helps mount the fuel pump, there's a circular rubber gasket/grommet/seal thing on the bottom where the sock is. Undo the hose clip on the short fuel hose on the side to disconnect it from the 3 way distribution pipe to be able to lift the upper half away. Don't forget to unplug the fuel pump too! There's a few rubber O rings that will need transferring to the new filter housing, I show these in the video at the bottom of this write up. Reassembly is the reverse Here's a photo of the new filter installed, you'll be able to see where the tabs are more clearing against the yellow OEM plastic Once the assembly is re-installed, I turned the engine over a few times to help build up fuel pressure. I did panic when the car stopped turning over but I could hear the fuel pump making a noise. It eventually started and has been fine since. Found my 'lucky' coin underneath the rear seat too The Youtube video can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44&t=6s
    • It was picked up on the MOT/Inspection that the offside front wheel bearing had excessive play along with the ball joint. It made sense to do both sides so I sourced a pair of spare IS200 hubs to do the swap. Unfortunately I don't have any photos of the strip down but here's a quick run down. On the back of the hub is a large circular dust cover, using a flat head screw driver and a mallet I prised it off. Underneath will reveal a 32mm hub nut (impact gun recommended). With the hub nut removed the ABS ring can be removed (I ended up using a magnetic pick up tool to help). Next up is to remove the stub axle, this was a little trickier due to limited tools. I tried a 3 leg puller but the gap between the hub and stub axle wasn't enough for the legs to get in and under. Next option was a lump hammer and someone pulling the stub axle at the same time. After a few heavy hits it released. The lower bearing race had seized itself onto the stub axle, which was fine because I was replacing them anyway. With the upper bearing race removed and the grease cleaned off they looked like this The left one looked pristine inside but gave us the most trouble. The right one had some surface rust but came apart in a single hit, figure that out?! I got a local garage to press the new wheel bearings in, reassemble was the opposite and didn't take long at all. Removing the hub itself was simple. Starting with removing the brake caliper, 2x 14mm bolts for the caliper slider and 2x 19mm? for the carrier > hub bolts. I used a cable tie to secure the caliper to the upper arm so it was out of the way, there's a 10mm bolt securing the ABS sensor on. With the brake disc removed from the hub next are the three castle nuts for the upper and lower ball joints and track rod end. Two of these had their own R clip and one split pin. A few hits with the hammer and they're released (I left the castle nuts on by a couple of turns), the track rod ends gave me the most grief and I may have nipped the boots (oops). Fitting is the reversal and is very quick and easy to do. The lower ball joints are held onto the hub by 2x 17mm bolts. The castle nut did increase in socket size to 22mm from memory (this may vary from supplier) The two front tyres weren't in great condition, so I had those replaced with some budget tyres for the time being. I'll be replacing the wheels and tyres in the future, this was to get me on the road without the worry of the police hassling me.
    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
×
×
  • Create New...