Jump to content
SAU Community

New Mods ?

r33gtstjeff
 Share

Recommended Posts

r33gtstjeff Apprentice

r33gtstjeff

Posted
Posted

hey just wanted to get an opinion of what u think i should an can do to my r33gtst with $2000.00.. has got greddy bov, hks pod, 3'' exaust from dump back an is boosted to 12psi already..! was thinking of frontmount an dump.. uping boost to 15psi.. i can get that done for around $1500.00.. so still got alittle to play with untill such time.. what do u think? dont want to do all that much to it but..!??? should that give me a good power gain..?

Link to comment
https://www.sau.com.au/forums/topic/275677-new-mods/
Share on other sites
mad082 Grand Master

mad082

Posted
Posted

adding a dump pipe won't increase the boost unless it is a poor design and doesn't alloy the wastegate to flow properly.

unless you have an aftermarket ecu you won't be able to run 15psi anyway, although you would gain power from doing it, but you may find your turbo doesn't last very long before it goes on a diet (and the exhaust wheel comes off the turbo and makes friends with your catalytic converter)

if a dump pipe is costing you $1500, i really suggest you find a new place to shop unless you get a shag every night for a week from a really hot chick with it. just get a cheap split dump pipe for about $100. i had one on my 33 and it worked fine.

i would also get a fmic kit, especially if you are running 12psi through the stock one. the stock cooler will suffer heat soak after only a few hard accelerations and basically won't be doing much cooling after that.

Link to comment
https://www.sau.com.au/forums/topic/275677-new-mods/#findComment-4669810
Share on other sites
r33gtstjeff Apprentice

r33gtstjeff

Posted
  • Author
Posted
adding a dump pipe won't increase the boost unless it is a poor design and doesn't alloy the wastegate to flow properly.

unless you have an aftermarket ecu you won't be able to run 15psi anyway, although you would gain power from doing it, but you may find your turbo doesn't last very long before it goes on a diet (and the exhaust wheel comes off the turbo and makes friends with your catalytic converter)

if a dump pipe is costing you $1500, i really suggest you find a new place to shop unless you get a shag every night for a week from a really hot chick with it. just get a cheap split dump pipe for about $100. i had one on my 33 and it worked fine.

i would also get a fmic kit, especially if you are running 12psi through the stock one. the stock cooler will suffer heat soak after only a few hard accelerations and basically won't be doing much cooling after that.

nah..! that price includes the dump,r33 front mount and fitted an a service..! not to bad.. cheap. think ill keep the 12psi but.. dont want to kill the turbo.. yet!

Link to comment
https://www.sau.com.au/forums/topic/275677-new-mods/#findComment-4670098
Share on other sites
r33gtstjeff Apprentice

r33gtstjeff

Posted
  • Author
Posted
$2k?

I would spend 600 on a stage 2 advanced driving course and 1400 on a set of track tyres. you've already got everything else you need to go quick in the car

u dont think i need a front mount an dump pipe to give that little extra..?

Link to comment
https://www.sau.com.au/forums/topic/275677-new-mods/#findComment-4670107
Share on other sites
r33gtstjeff Apprentice

r33gtstjeff

Posted
  • Author
Posted
you do NEED a front mount. as mad082 mentioned earlier that the stock cooler will be suffering from heat soak.

get the dump pipe.

go get a nistune done as well and that will keep you happy for the time being.

yer i think that is the go for sure.. do u think that will give me close to 200rwkw..? thats really all iam aiming for off this car.?

Link to comment
https://www.sau.com.au/forums/topic/275677-new-mods/#findComment-4670312
Share on other sites
mad082 Grand Master

mad082

Posted
Posted

the issue with the stock turbo is the ceramic exhaust wheel. when they are highflowed they usually have a steel wheel put on (as where it sits is made larger so needs a larger wheel). the limit to what you can run then is then down to mods and what pressure it stops making power, but would be well above 15psi

Link to comment
https://www.sau.com.au/forums/topic/275677-new-mods/#findComment-4673653
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • 04-LOOX
      R34 GTR Vspec Garage Sale - All must go!

      By 04-LOOX · Posted

      Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...