Jump to content
SAU Community

Recommended Posts

i got a r33 series 1 skyline 93 model...and im thinking of converting the gearbox from auto to manual coz im sick of driving auto..

Is it worth it?...how much would u think it cost for the gearbox plus labour??

any tips? i got a rb25-det engine btw

Link to comment
https://www.sau.com.au/forums/topic/275889-r33-auto-to-manual-is-it-worth-it/
Share on other sites

There's more to the conversion than just swapping the gearbox, much more.

Sell your auto and buy a manual. Don't go converting a vehicle that came so widely distributed as a manual :whistling:

i just did mine, picked it up 2hrs ago. love it to bits. in the end the whole conversion cost me $2k installed... hoping to get some money back from selling all the bits.

$2k? dats alrite...but after seing ur other post it has side effects/problems but anywayz yea i should just buy a manual...god dammit why did i buy an auto LOL...the car looks good though

Nothing wrong with the auto gearbox ... just modify the valve body ...

Either a stage 2 shift kit or stage 3 full manual valve body upgrade

Stage 2 shifts are pretty hard and alot quicker than a stock gearbox ...

I have the stage 2 in mine and it has no trouble kicking the rear end out and im running a N/A R32 GTS RB20DE

I am also running a Series 2 R33 GTS-T Auto gearbox in mine

2k! goddamn! was 4k the last i checked. which was the price diff between auto and manual cars anyway. mates rates?

nah, bought the conversion off ns.com from a dude, then got a workshop to install it.

$2k? dats alrite...but after seing ur other post it has side effects/problems but anywayz yea i should just buy a manual...god dammit why did i buy an auto LOL...the car looks good though

yeah it turned out that the manual conversion on r33's is a bit more involved than other nissans (32, 180sx, 200sx, silvia), in other cars you only swap over the auto loom to manual one, however r33 has different harnesses between auto and manual and you have to re-wire and make your own small loom. Its fairly straight forward from what the mechanic told me, just gotta know which wires to use and which ones to remove.

The car is running great again :down: loving the manual!!!

Edited by SkyHi_33

sure did mate! thanks for all your help really appreciate it ;)

goes so much harder with manual :) still keeping me over the moon hehe just need to swap out the dash cluster and were done.

Edited by SkyHi_33

yeh it depends how attached you are to your current car... selling mine and buying a manual one wasn't an option for me because ive already done a heap of suspension and brake upgrades to it and spent many long hours working on it, so wasnt worth pulling it all out and repeating the process on another car.

good luck with your decision tho! i think you will find that the 180sx is a lot more sportier and agile to the skyline but you will miss the comfortable interior and the inline 6 torque :P

Was gonna buy a new car but changed my mine..Its not worth buying a new car either especially if ur gonna buy from the dealers..The cars are expensive and paying finance is not worth it...

anyway hook me up skyhi i wanna do the conversion too! :D

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Stock ECU (or more accurately stock tune) absolutely refuses to go over 10psi and behaves like you have seen. The Nistune is the same if it is the stock tune. If the Nistune chip has been tuned, the resulting tune could be literally anything for any combination of parts. The Nistune just makes the stock ECU Tunable.
    • So stock ECU does not like anything above 10 psi?  That Nistune one is just for "try" if it will be any different, I know it need to be tune for that. I know but YOU may know about these problem but i/we dont. They few little Skylines here let alone people who know anything about tham so that is why iam asking here  
    • So now we have a radiator with no attachments whatsoever. It lifts up with a particularly tight spot between the drivers side air box mount and the lower radiator outlet, but if you've got this far you will sort that too. This is the lower mounts with the rad out so you can see where the rubber bushes go, it is a straight shot upwards Done! Assembly is the reverse of disassembly, with blood less likely to be shed.
    • Right, onto the second last trick. The Air Con condenser is mounted to the front of the radiator and stays in the car when the radiator is removed. There are 2x 10mm headed self tappers holding the top of the condenser to the radiator, remove those The bottom of the condenser is attached to the radiator with clips. You need to lift the condenser out of those clips and clear (up, then forward). f**ked if  could work out how to do that last bit with the front bumper on. I hope you can, and you share the trick.  Bumper removal probably deserves its own thread one day once I've recovered the will to live, but basically you need to remove the wheels, front inner guard liners (clips and 10mm headed bolts), the self tapper between the guard and the bumper at the rearmost point of the bumper (same as an R32 that bit), any remaining clips at the top/front of the grill, an absolute bastard design with a plate that holds the top of the bumper above the headlight each side (only 1 bolt which is tricky to get to, but the plate catches 2 places on the bumper and must be removed....carefully!) and push clips between the bumper and guard under the headlight. If you've done all that you will be faced with wiring for the fog lights on both sides and in ADM Q50 RS at least, 4 nasty tight plugs on the driver's side for the ADAS stuff. So, the clips at the bottom look like this on drivers side (looking from the front) And on the passenger side (also from the front), you can see this one is already out Clearance on both of these are super tight; the condenser needs to move up but the upper rad support mount prevents that, and the radiator can't move down far because it is (rubber) mounted. Once you achieve the impossible and drop the condenser off those mounts so it does not stop the rad moving, you are good to go
    • OK, next the shroud needs to come off and there are a couple of tricks. Firstly, there is a loom from near the passenger side headlight to the fans, coolant temp sensor etc and there is no plug to undo.  In my case I was OK to leave the shroud on top of the engine so I just undid the passenger side fan plug and about 10 of the clips which gave enough free wire to put it aside. The fan plugs were super tight, the trick I used was a small falt screwdriver to push down on the release tab, then a larger flat screwdriver to lever the plug out of the fan unit....be careful with how much force you apply! If you need to remove the shroud altogether for some reason you will have to deal with all the plugs (tight) and clips (brittle)....good luck. I removed all of the clips and replaced them with cable ties that I will just cut next time. Also, in the Red Sport / 400R at least, the intake heat exchanger reservoir hose is bolted to the shroud in 2 places with 10mm headed bolts; so remove them (the hose stays in the car; no need to undo it at the t fittings down at the radiator lower mount. Once you've dealt with the HX hose and the wiring loom, there are 3x 10mm headed self tappers holding the top of the shroud to the radiator; remove those.   The shroud then lifts out of the bottom mounts where it sits on the radiator, up and onto the engine out of the way. Simples
×
×
  • Create New...