Jump to content
SAU Community

Recommended Posts

lol smells like a spam bot (seeing as he has the brand name he mentioned in his nick), but oddly its on topic and in the right section. haha has me second guessing. My guess is its a way to get Google search results hits when someone searches for "welding aluminium with a mig".

but back on topic, I'm thinking of buying a MIG, but wanna be able to do aluminium welds too. do I have to get one that's capable of really low voltages as the aluminium I wanna weld is pretty thin?

Shan, same smell i got from it haha - the thing that gave it away most was the automated template used, that worked on the other thread in the US

Alloy welding requires more amps than mild steel, but as VB- stated nylon liner is best practice along with the correct gas shield- depending on the mig you get, you could get a spool gun for it that holds the roll on the gun to stop binding in the gun.

so what are YOU doing on a US based Z forum craved? good tech/fab sections on there or anything?

can you still get those push-pull guns? havent really seen em around (bar the ancient ones floatin round the shop/at trade school)

I can weld down to 1mm fillet and butt welds at work, but that is on WIA 450 industrial machines with a 'softarc' setting. But that setting my only be an Incat program.

At home, I have a WIA 175 which I weld mild and ally with. Coiled steel liner for steel, nylon for ally. Use .9mm or 1.0mm ally wire with Argon gas, no mixes, just Argon.

Did I mention my trade is Aluminium welder / fabricator?? *lol*

Cheers, Greg.

  • 4 weeks later...

as above!! use pure argon and nylon liner. the liners usually dont last that long tho

i welded heaps of alum with mig but nuthin under 4mm plate

i would say a mig weld that thin would sit on top of the metal more than a tig weld which tends to "sink in"

that was my experience. btw i was using .9 and it welded 4mm up just fine

was on a unimig 165.

  • 2 months later...
I can weld down to 1mm fillet and butt welds at work, but that is on WIA 450 industrial machines with a 'softarc' setting. But that setting my only be an Incat program.

At home, I have a WIA 175 which I weld mild and ally with. Coiled steel liner for steel, nylon for ally. Use .9mm or 1.0mm ally wire with Argon gas, no mixes, just Argon.

Did I mention my trade is Aluminium welder / fabricator?? *lol*

Cheers, Greg.

how do you go welding steel with pure argon ive never tryed it but from what ive herd it doesnt penetrate really good if it works well i would love to no as ive got a mig and i just bought a tig and really dont want to have 2 bottles

thanks tim

  • 3 weeks later...
  • 1 month later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Well, yes, every CU on the bus is available via the Consult port, but whether the scanner you are using is capable of talking to the TCU, the ABS/TCS modules, etc etc, is what is at question here. Many of them are only for engine codes. So, if you have one of those, you won't know if the ABS is having a bitch.
    • That's now. R chassis Skylines come from a time when the tolerance in the ADRs was a bit more....slack. My car, on 235/35-17, which is damn near the exact same size as the original 205/55-16, is pretty much bang on correct indicated speed across the whole legal range. That's demonstrated with constant speed run over 5km, and GPS speed. It's just the luck of the draw. My particular speedo head has to be the thing that is "calibrated" that way, because everything else (the diff ratio, the gearbox and the speedo drive**) are all same same as most other Skylines. **OK, so the speedo drive is a Navara unit to drive the R32's cable, not the electronic unit than an R33/4 would normally have with teh same gear on it. Otherwise, I applaud your OCD tendencies, and I would do the same if I needed to.
    • Not too sure, I believe the Nissan consult port does everything? Also just filled up the reservoir to full and the light is still on. The float seems to move up and down fine.
    • The speedo's can be very conservative, when my Mazda NC MX5 speedo is showing 118kph, the GPS, and a calibrated radar.... cop mate.....hits me at around 110kph +/- 1 or 2 kph, and that is on a 215/45 17, stock tyres size is 205/45 17 as well, so weirdly conservative with stock tyre size When my Commodore speedo red 116kph GPS had me at 110kph on 255/40 17, so again conservative Google says manufacturers need to set the speedo from 4 to 10% slower than actual road speed.....for safety.....and compliance  After doing some offset and clearance measurements to see what can fit the NC on 17x8 +40, without guard rolling or rubbing anything at my current ride height, I've decided that when my tyres are toast, I'm going to fit 225/45 17 and see where that gets me IRT actual speed of my speedo and GPS/radar From the online calculator I should be still be doing around 5kph under an actual 110kph when the speedo is showing 110kph My ADHD requires that when I'm doing 110kph on the speedo, that the actual road speed is actually really close to that, and not alot slower And going from 205 to 225 still keeps the car within the %/mm allowable in the NSW vehicle rules and regulations, which is nice, as long as I'm looking at the latest version that is.....LOL https://www.nsw.gov.au/sites/default/files/2021-02/RMS-13.464-Light-vehicle-modifications-Vehicle-Standards-Information-No-6-November-2013.pdf
    • Take the value it measured as, and pick the closest range available that is above the reading on the screen.   Also, no point just testing the coils. Read what has been said again. You need to test all your wiring, everything.
×
×
  • Create New...