Jump to content
SAU Community

Recommended Posts

Hi Guys....

As allways, if there is something wrong, go to the guys with the info, as all that i've inquired about through this forum has lead to good info, i'm tryin again...

ok, my rear shocks on my m35 are leaking...i.e they're poked. so nissan will sell me genuine ones but to fit 2 new rears will be about $1000 and it seems getting aftermarket ones in new zealand is impossible as most peoples parts catalogues dont list an m35 to start with. i'm wondering what i need to ask for,

are they the same as v35 skyline ones?

what have you guys used?

are they the same as any other models aswell?

any help would, as allways be greatly appreciated.

Link to comment
https://www.sau.com.au/forums/topic/278161-m35-stagea-shocks-help/
Share on other sites

Hi Guys....

As allways, if there is something wrong, go to the guys with the info, as all that i've inquired about through this forum has lead to good info, i'm tryin again...

ok, my rear shocks on my m35 are leaking...i.e they're poked. so nissan will sell me genuine ones but to fit 2 new rears will be about $1000 and it seems getting aftermarket ones in new zealand is impossible as most peoples parts catalogues dont list an m35 to start with. i'm wondering what i need to ask for,

are they the same as v35 skyline ones?

what have you guys used?

are they the same as any other models aswell?

any help would, as allways be greatly appreciated.

As far as I know they are pretty unique.

at $1000 for rears alone, I would look at Tanabe NF coilovers - I just ordered a set at $1580 for all 4 - they are height adjustable and use the same spring rate as standard. Damping is a little firmer just to reduce body roll and excess bounce around corners. I got mine from JDM Concepts. I should have them in a week, but I have heard really positive feedback from other forum members using the same shocks.

Note* Apparently they wont work with HICAS (4 wheel steer) model M35's

if you have an ARX your selection is fairly limited but if you have an RS or RX then there is a larger selection available.

do a search on this and there is a large thread with this covered, also iamhe77 has kindly made a thread with many different brands of after-market suspension kits available for the M35.

i really do not understand the fact hicas matters or not

I think that is why the rear shock is bolted into the "top hat" that then bolts to chassis. I would presume that allows to shock to have some lateral movement without causing any problems.

$1k for the rears alone!!!! F*ck me!!!

Depends what you want.

If you need them to be height adjustible, look at Bilsteins or by all means go through the M35 Aftermarket Suspension thread and make your choice, than email RHD to get it listed and buy through them (you usually get a 5% discount if you buy the item you get them to list).

If you don't need height adjustment, go with the Nismo's.

RHDJapan has them listed new and will ship to NZ, just create an account.

RHDJapan is HIGHLY recommended for all new stuff :)

Edited by iamhe77

I would not consider the standard Nissan shock as it is a twin tube shock and not particularly good.

If you are going to replace them I would get something of a little better quality and at least a single tube design.

Cheers

Andy

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
    • For race cars, this is one part where I find having the roll cage bar having gone through a hole in the floor better than the build it up on a ledge inside... The Merc I help on, the main hoop ends are marked on the car, and the jack is marked... Jack goes under a few inches and lifts one whole side of the car up... Removes that fight for long slim jacks for race car duties!   My biggest issue for the daily drivers I work on, is my jacks don't go high enough. The jacks start out on a few blocks, jack it up, then start a second jack under it on more blocks, and then I can get an axle stand under it. My axle stands are presently in use, and are nearly fully extended. The car is sitting with barely more than a cm of clearance to get the wheel off the studs! Sarah's Kluger is the same, as it has an ungodly amount of droop available in the suspension and a distinct lack of good jacking points!
    • Happy? Yep, my to do list is getting shorter and shorter. Either this light approaching is the end of the tunnel, or I'm about to be hit by a train... Ha ha ha   Also, Duncan isn't that far out of town that you need to make a multi day drive out of it. 😛
    • Sorry I meant that we are building the EH for a client.
    • LOL, when one "money pit" is never enough Noice, and excellent work mate
×
×
  • Create New...