Jump to content
SAU Community

Recommended Posts

It all comes down to what outcome you want from your vehicle.

Nistune around $450 mark.

Vipec $2500-3000 mark.

You do the math's.

Putting these two ECU's together is like saying, I'll race you in my R34 GTR when you own a S13 Ca18, you cannot compare them.

Bang for your buck, nistune, however you will out grow it if you want to make big big power.

  • Replies 67
  • Created
  • Last Reply

Top Posters In This Topic

How nwill you outgrow nistune, when the japs have been using th esame principle to make 1000hp. For the cost of the vipec, which is totally overkill for your setup, i would go nistune, buy your own wideband and have a crack. Or go nistune and take it to sydney/canberra. If your guy cant tune nistune then i wouldnt trust him with your car even if its a vipec. Remember even with the vipec it could still run like crap, as its only as good as the tune.

psymon, I think I recall tuning your old setup in canberra?

have you changed injectors or afm? are you still running the stock 270cc injectors?

Yeah you did a couple for me in canberra. The last one you did was to suit gtr injectors and was a great tune. :) Still gtr injectors, but i now have a z32 afm to put in one weekend.

As for the tuner, it's not that he can't tune a nistune, its more that he's never done one before but he's done multiple vipecs. I'm sure if i turned up with a nistune he could tune it, he's built tuned many respectable cars (including his own which was featured in the latest series of blood sweat and gears). It would just be reassuring with the vipec knowing it's not the first he's done.

I was intending to go with Nistune on a >300rwkw 26/30 but figured that after $450 for the ecu, $700 on two Z32s and $650 on a good ebc I was over the cost of the Vipec board + mac valve. Even with one Z32 it's close in cost. I don't have to worry about AFMs, and also get overboost protection and some other features.

It was the $ and overboost protection that made my mind up. And if your tuner likes Vipec it's also a plus to stick with that, although for a 5 hour trip to Sydney I'd say (having had 2 Vipec tunes, one of which was by a proclaimed Vipec specialist, but neither of which was very good) go to Hitman in Penrith, leave it for 2-3 days, pay your $1250 and come away with a great tune - power and driveability - as well as emissions certification.

Just my 2c.

Edited by Scooby
Go with what your tuner says...

I don't know Nistune (is that just re-tuning the standard ecu?) but I know vipec... as much as I want DiRT Garage to shut the f**k up about it, it's still a very good ecu...

no need to be a c0ckhead Doof.

Im about to go Nistune in my S13...better than Power FC...Nistune has knock control.

If you have the bucks go Vi-PEC especially if your tuner is familiar with them.

no need to be a c0ckhead Doof.

Im about to go Nistune in my S13...better than Power FC...Nistune has knock control.

If you have the bucks go Vi-PEC especially if your tuner is familiar with them.

Yeah Doof, cut it out. We dont need 2 cockheads crappin on about ecu's :laugh:

Bang for your buck, nistune, however you will out grow it if you want to make big big power.

How much is big big power?

It would be safe to say 90% of users on here have stock motor internals so there max power goals are going up to be a approx max of 280-300rwkw.

Will the Vipec or any other full stand alone ecu have a noticable difference over the Nistune for these power levels?

The Vipec has a long list of extra features, but will they be used or needed for a daily driven street car?

Can some list what these great extra features any stand alone ecu have over the Nistune to justify the extra exspense?

ps. I have done a fair bit of searching on here about the pro's and cons of either ecu option. Generally everyone says one is better than the other, but do no state why to back their claims. There is one very well respected tuner on here from Melbourne that tunes more than one brand and agrees the Nistune is the best option for a Neo rb25 for the street)

if that is your intended mod list, nopoint spendingbig bux for vipec,

look at power FC or even cheaper option, the emanage blue or something.

im sure he can tune the emanage,

to tune the nistune, he needs to get the licence & software to do it.

^ its like neons on your car, unnecessary but just cool to have it :laugh:

How much is big big power?

It would be safe to say 90% of users on here have stock motor internals so there max power goals are going up to be a approx max of 280-300rwkw.

Will the Vipec or any other full stand alone ecu have a noticable difference over the Nistune for these power levels?

The Vipec has a long list of extra features, but will they be used or needed for a daily driven street car?

Can some list what these great extra features any stand alone ecu have over the Nistune to justify the extra exspense?

ps. I have done a fair bit of searching on here about the pro's and cons of either ecu option. Generally everyone says one is better than the other, but do no state why to back their claims. There is one very well respected tuner on here from Melbourne that tunes more than one brand and agrees the Nistune is the best option for a Neo rb25 for the street)

the "great extra features" are launch control, anti-lag, flat shifting, Map sensor instead of AFM (though it will take an AFM if you want), built in boost control with the addition of a solenoid, onboard data logging, dual fuel and ignition maps with real time change over (you wire in a switch to do so)(E85/other fuel tune and your standard 98 tune for example).

There are probably other things i have missed but they are the main ones that come to mind.

the "great extra features" are launch control, anti-lag, flat shifting, Map sensor instead of AFM (though it will take an AFM if you want), built in boost control with the addition of a solenoid, onboard data logging, dual fuel and ignition maps with real time change over (you wire in a switch to do so)(E85/other fuel tune and your standard 98 tune for example).

There are probably other things i have missed but they are the main ones that come to mind.

Nearly all of those features I would not need or use. . . . already have a z32 and ebc.

Do not get get me wrong, I will be more than happy to hand over the extra $1000 if there is going to be a real noticable benefit.

Yeah you did a couple for me in canberra. The last one you did was to suit gtr injectors and was a great tune. :( Still gtr injectors, but i now have a z32 afm to put in one weekend.

As for the tuner, it's not that he can't tune a nistune, its more that he's never done one before but he's done multiple vipecs. I'm sure if i turned up with a nistune he could tune it, he's built tuned many respectable cars (including his own which was featured in the latest series of blood sweat and gears). It would just be reassuring with the vipec knowing it's not the first he's done.

psymon,

I have another idea that might help. I would be more inclined to make the drive to sydney and make a weekend of it. there are some top tuners there and you can choose either nistune or vipec there. nistune will do a good job for what you are looking for.

if you need a map to drive the car to sydney safely with the z32 installed and your other bits I can burn one and send it to you.

cheers...

psymon,

I have another idea that might help. I would be more inclined to make the drive to sydney and make a weekend of it. there are some top tuners there and you can choose either nistune or vipec there. nistune will do a good job for what you are looking for.

if you need a map to drive the car to sydney safely with the z32 installed and your other bits I can burn one and send it to you.

cheers...

Thanks for that. I'll keep it in mind in a couple of weeks when i have to make a decision.

if that is your intended mod list, nopoint spendingbig bux for vipec,

look at power FC or even cheaper option, the emanage blue or something.

im sure he can tune the emanage,

to tune the nistune, he needs to get the licence & software to do it.

^ its like neons on your car, unnecessary but just cool to have it :(

that is included in the price of the board (well single user licence anyway). $200 for the board and $200 for the licence. so you are looking at $400 plus tuning. so even if it costs you $1000 in tuning you are still coming out ahead of just buying a vipec

  • 2 weeks later...
when fitting a vipec where do you place ther air temp sensor also is it wired independently

in the plenum or inlet piping. it is wired to to one of the temp. inputs. In a GTR it uses the factory sensor but cars like a gts-t that dont have an inlet temp sensor you have to use the sensor provided with the ECU.

My tuner can use an emulator and write/tune the factory ecu. The process is similar to Nistune, but doesn't require the Nistune daughter board. He still has to

-open the ecu,

-remove one of the processor chip,

-put it onto a reader and copy the complete firmware,

-transfer the program to the laptop,

-hook the laptop to the factory computer (where the chip was),

-tune the car,

-then write the file to the removed processor chip,

-resolder the chip back to the factory ecu.

This method retains all of the factory safety parameters e.g. knock control, over heat etc but also can adjust the factory boost solenoid (and possibly the MAC valve).

I think Dave @ Silverwater Automotive Service in your state can do the same thing.

I would expect the Nistune can adjust the factory boost controller (or a mac valve) too. So you can save the money by selling your boost controller.

My tuner can use an emulator and write/tune the factory ecu. The process is similar to Nistune, but doesn't require the Nistune daughter board. He still has to

-open the ecu,

-remove one of the processor chip,

-put it onto a reader and copy the complete firmware,

-transfer the program to the laptop,

-hook the laptop to the factory computer (where the chip was),

-tune the car,

-then write the file to the removed processor chip,

-resolder the chip back to the factory ecu.

This method retains all of the factory safety parameters e.g. knock control, over heat etc but also can adjust the factory boost solenoid (and possibly the MAC valve).

I think Dave @ Silverwater Automotive Service in your state can do the same thing.

I would expect the Nistune can adjust the factory boost controller (or a mac valve) too. So you can save the money by selling your boost controller.

I've got no problem with either ECU as both if tuned properly will deliver the same power and drivability. Dont let the knock control of the std ECU sway your judgement as from what I've seen it doesn't work very well at all. Thats why I'm thinking a Speed Density Visteon ECU with two knock sensors is what I will use if I ditched the std ECU.

easy

spend the dollars on a second hand pre-remapped RB20 ECU from japland

plus add in a safc

then tune tune tune, retune to be safe, and you'll love the bang for buck outcome that a remap + piggyback gives you :bunny:

or go NISTUNE and get the bloke to do it anyway - he's got to crack his cheery sometime !!!

my options:

a) remap + piggyback

b) nistune

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Welcome to my 2004 Toyota Mark ii IR-V Fortuna (series 2) With a 1JZ-GTE powerplant under the bonnet (hood) it'll give me plenty of scope for power upgrades. For those who aren't familiar with imports, the 1JZ-GTE is a 2.5L 6 cylinder VVTi engine with a single turbocharger. This has the factory R154 5 speed gearbox, along with a aftermarket 2 way LSD differential (brand unknown). Under the arches are a set of CST Zero 1 alloys, 18x9 +30 225/40 up front and 18x9.5 +15 265/35 on the rear. The car was quite low in Japan and there's evidence of the wheels catching the rolled arches/fenders. The tyre's aren't great so I'm in two minds whether to replace both or just the tyres and put up with the wider wheels on the rear. The car still uses stock brakes with the addition of some braided hoses. The exterior is stock with the exception of a BN Sports front bumper and a replacement Fortuna grill  Moving to the interior, the steering wheel has been replaced with a dished MOMO steering wheel (which will get swapped for my Momo Tuner for the time being) Defi Link Gauges are mounted above the climate controls and on the A pillar, the Oil Temp,Oil Pressure,Water Temp and Boost gauges should help with spirited and track driving  The stock seats have been replaced with some retrimmed Recaro bucket seats. Being a larger build these are a little snug, unfortunately the orange isn't for me so I'll look into replacing these down the line. Other modifications include a twin plate clutch, Blitz intercooler, Evolve alloy radiator, a stainless exhaust with decat, HKS EVC-S boost controller and coil overs
    • Apologies for the long read My R34 GTT was up for sale at the beginning of spring due to a few repairs creeping up. The strut tops needed replacing, roof and bonnet (hood) painting (yay for 3 stage pearl) and the underside stripped and treated. I sold the car which allowed me to be in a much better place financially. Leading up to the sale I was already thinking about the replacement. In an ideal world it needed to be a good all-rounder. Something I can mess around with, modify, do track days, do the school run, go on long drives etc.  Options included but not limited to... Laurel C35, Evo 8/9, Civic FD2, Impreza Hawkeye, Aristo and even an Audi S4 Avant (I've already got the Mazda 6 wagon). But there was always one car at the top of the list The Toyota Mark ii JZX110 I found an advert on a Facebook group for an example in Japan, from a seller called Jon at Rising Sun Exports. A few messages back and forth and Jon calls me from Yokohama one morning (or afternoon in his case). He briefly explained the import process, the costs involved and a repeat of the advert. After much deliberation, the price was agreed and the sale was locked in. I've never imported a vehicle so I jumped into the unknown head first. The money transfer was completed through wise.com (fees apply), very easy to use and the money was with him within a day or two.  The car suspension was raised for the vessel and the car dropped off at the port. It was 7 weeks later when the bill of lading was received and the freight invoice sent to me, followed by the export certificate a couple of days after (both digital copies) In the mean time the port had been in contact. I needed an agent to deal with the NOVA (notification of vehicle arrival) along with the tax/duty invoice, this was £75.00. The port also had a fee of £100, I'm guessing to cover the cost of the 10 day 'free storage' and for moving the car off the boat etc. They need a copy of the vehicle invoice, freight invoice and export certificate to allow the vehicle to pass through customs. The vessel arrived on Tuesday 5th August, the tax/duty invoice was generated and sent over. This is generally tax 20% and duty 10% of the vehicle value. Although the invoice came in at a higher amount than I had calculated. Once HMRC had received the payment the vehicle could be released from customs. I thought once the tax/duty was paid you could collect at any point, that's not the case. Your agent will need to book a collection slot, I requested Thursday 7th which was accepted, with a 9:00am slot allocated. It was a 5:00am start from Norfolk heading to Southampton. We eventually found the compound, upon presenting the bill of lading and some ID they released the car (they drove it out of the compound to the front ready for us to load up). The email from the port stated each slot had a 10 minute window, which seemed abit farfetched but the staff said it's not a strict rule. We were there for approx. 30-40 mins in total. A week prior to collecting I contacted my garage and explained the situation, I was able to get an inspection slot that afternoon. For the registration, DVLA require the car to be insured, for this I used a company called Adrian Flux who can insure the vehicle using the VIN number. 
    • Hey guys, looking for these side skirts if anyone can help me out. 
    • Wife and I are still looking for a new home. One condition was a large enough garage for a full-size lift in one bay. Now if only we could find something... We've been looking for almost a year now.
    • Thanks everyone for the ideas! Sadly, ramps are a no go for me. With young kids at home, I do most of my work late at night while they're sleeping. Starting the car multiple times wouldn't be a great idea.  I'll go see one of those new long reach low profile jacks and take a couple measurements to see if they will fit.   
×
×
  • Create New...