Jump to content
SAU Community

Recommended Posts

Hey im assuming this is fairly normal granted its been pretty cold?? Drips a bit of water too. It all stops once its warm?

Just dont remember my old clubsport doing it quite as much...

If it stops when warm its nothing to worry about! Mine does the same when cold.:D

Link to comment
https://www.sau.com.au/forums/topic/278906-r33-gts25t/#findComment-4711510
Share on other sites

+1 to the mentioned above.....my car blows a heap of smoke when cold start and as soon as it warms up a bit then its all sweet......just try not to drive it when its really cold lol

nothing to worry about mate

Link to comment
https://www.sau.com.au/forums/topic/278906-r33-gts25t/#findComment-4711527
Share on other sites

don't warm up your car in the morning. bad for your engine. wears your plugs, allows unburnt fuel to condense and drip down past your rings into your oil diluting it.

more relative to what you're talking about, if you warm it up for like three to ten minutes it will take MUCH longer to get rid of the water vapour. Doesn't hurt your engine... it's what it's designed to do. Warming up for 5 minutes is an old wives tale. or husbands. either way, it's lame and misguided.

best way to warm up your car in the morning and get rid of the water vapour is to nanna it until it reaches just under operating temperature (a safe temp is about 70-75°, suitable op temp being between 80° and 95°C).

Try it out, the lot of you. If there's one thing you can trust, it's a dude on the internet. (That dude is Doctor Karl, bitches.)

Edited by Dorigecko
Link to comment
https://www.sau.com.au/forums/topic/278906-r33-gts25t/#findComment-4712933
Share on other sites

don't warm up your car in the morning. bad for your engine. wears your plugs, allows unburnt fuel to condense and drip down past your rings into your oil diluting it.

more relative to what you're talking about, if you warm it up for like three to ten minutes it will take MUCH longer to get rid of the water vapour. Doesn't hurt your engine... it's what it's designed to do. Warming up for 5 minutes is an old wives tale. or husbands. either way, it's lame and misguided.

best way to warm up your car in the morning and get rid of the water vapour is to nanna it until it reaches just under operating temperature (a safe temp is about 70-75°, suitable op temp being between 80° and 95°C).

Try it out, the lot of you. If there's one thing you can trust, it's a dude on the internet. (That dude is Doctor Karl, bitches.)

:D

Link to comment
https://www.sau.com.au/forums/topic/278906-r33-gts25t/#findComment-4713035
Share on other sites

while it is a bit off topic, i am also against the letting your car sit there and idle to warm up. the main reasons being that it takes longer for a car to warm up when it's just sitting there idling, which means the car is running for longer at colder temps. the other reason being that it doesn't warm up the oil in the gearbox or diff.

another thing to take into consideration is that if you run your car for 10 mins every morning before you start driving, over a 1yr period, that is nearly 61 hours of running that your engine has done that hasn't been taken into account on your odometer, which means more than likely not taken into account on your servicing frequency. and not to mention the extra fuel you are using.

Link to comment
https://www.sau.com.au/forums/topic/278906-r33-gts25t/#findComment-4713470
Share on other sites

30-60secs then I drive it. Stagea (being auto) I cruise along at 1500rpm while people behind me hurl abuse. Skyline I shifted at around 1000rpm (3L ftw :blink:) till it was out of cold start (>65deg).

Just don't load it up.

Edited by bubba
Link to comment
https://www.sau.com.au/forums/topic/278906-r33-gts25t/#findComment-4715420
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The oil pressure sensor for logging, does it happen to be the one that was slowly breaking out of the oil block? If it is,I would be ignoring your logs. You had a leak at the sensor which would mean it can't read accurately. It's a small hole at the sensor, and you had a small hole just before it, meaning you could have lost significant pressure reading.   As for brakes, if it's just fluid getting old, you won't necessarily end up with air sitting in the line. Bleed a shit tonne of fluid through so you effectively replace it and go again. Oh and, pay close attention to the pressure gauge while on track!
    • I don't know it is due to that. It could just be due to load on track being more than a dyno. But it would be nice to rule it out. We're talking a fraction of a second of pulling ~1 degree of timing. So it's not a lot, but I'd rather it be 0... Thicker oil isn't really a "bandaid" if it's oil that is going to run at 125C, is it? It will be thicker at 100 and thus at 125, where the 40 weight may not be as thick as one may like for that use. I already have a big pump that has been ported. They (They in this instance being the guy that built my heads) port them so they flow more at lower RPM but have a bypass spring that I believe is ~70psi. I have seen 70psi of oil pressure up top in the past, before I knew I had this leak. I have a 25 row oil cooler that takes up all the space in the driver side guard. It is interesting that GM themselves recommend 0-30 oil for their Vette applications. Unless you take it to the track where the official word is to put 20-50w oil in there, then take that back out after your track day is done and return to 0-30.
    • Nice, looks great. Nice work getting the factory parts also. Never know when you'll need them.
    • Thanks @jtha7 I will have a look around tomorrow but it is a prick of a spot. These are some photos i tried taking 
    • I take it that the knock retard is from bearings tapping a little tune? Thicker oil is a fragile bandaid. You need a much bigger oil cooler and probably the bigger pump being discussed.
×
×
  • Create New...