Jump to content
SAU Community

Recommended Posts

Hi, I just find out my 34gtr's water temp was up to 95-98 degree? is that normal?? but when i drive on highway there is only 77-80 degree.

thats really a big different between more air flow and less air flow.

I checked my fans its working good.

anyone can point out is this normal??

thanks!!

depends on where you fit the water temp sensor and atmosphere temperature But seems pretty normal to me.

98 degrees seems normal??

How did you test you fan, with mine it spins but i can stop it and even spin it backwards when its up to temp, this means its screwed, could be your problem as well.

Oopps Didn't notice its a GTR 34. if your stock Gauge displaying 98 degrees and on a slow rising mode then might want to check for water leaks or thermo related bits

Hi there is no leaking, the highest temp is 98degress, it will go down to 94 and rising up again.

but if the car runing the water temp will go down very quick. about 77-84 degree if drive normally.

i can see the highest water temp on the center screen is show up 98 degree in heavy traffic, but the standard water temp gauge only a little bit more than halfway.

and if the traffic flow is good or on the highway, the temp is about 80 degree, on standard water temp gauge is about halfway.

Edited by Nosure

No expert on R34 GTR's, but any car that registers above half on the stock gauge isnt a good thing?

Maybe your thermostat is stuck slightly closed, so when your in traffic its not quite opening enough for full flow.

Id try that before doing anything too drastic. Flush the system, new thermo, some good coolant..

98 is to hot for just normal driving on a daily basis for any RB. I don't know what hypergear is talking about. Did you try bleeding it to see if there is any air in the system?

Ive never seen above 90degrees, mostly 82.

only time i saw 89-90 was on a 40degree day during summer so i drove with my heater on full blast; took the temp down to 86-87 quite quick although heater + 40degree heat was unbearable lolz.

i agree with everyone, coolant flush for air pockets and new thermostat

the 98 degree only happend once on havey traffic. the car only run 300m in one hour.

in normal drive condition the water temp only about 75-85 degree. even i drive very hard the water temp still not go over 85.

and the fans is also OK. so I guess its normal if the engine is on and stay there for one hour.

the water temp only go high when the car doesn't move for a while.

98deg water temp is ok, it is a little high (check basics) but it wont kill the engine etc

just drive it normally once you are able to and the radiator has some airflow

once you drive it normally with airlfow, the temp should drop pretty reasonably to mid 80s

the ECU has correction based on water temp and will start taking out timing above certain levels

if water temp is near 110deg i would be worried - the stock guage cluster should be near 3/4 at this level

98deg water temp is ok, it is a little high (check basics) but it wont kill the engine etc

just drive it normally once you are able to and the radiator has some airflow

once you drive it normally with airlfow, the temp should drop pretty reasonably to mid 80s

the ECU has correction based on water temp and will start taking out timing above certain levels

if water temp is near 110deg i would be worried - the stock guage cluster should be near 3/4 at this level

thanks mate, so when the water temp up to 110, that mean problem?? or it will break some think?

You can warp the head for one. 98 isn't going to break anything, but it's higher than it should be. Mine gets a bit to hot one hot sunny days with the a/c going after I've been creeping along in traffic for too long. I turn the a/c off when it gets over 100 to let it cool back down. usually around 110-115 your coolant will start to boil.

Your coolant temp is very high for an RB engine, in heavy traffic I rarely go above 90c (13B-REW).

I'd have your lines bled and replaced with new coolant. But as stated in the thread your engine won't get damaged sub 120c, but you shouldn't be around that temperature at all even under extreme engine stress.

get the radiator professionally cleaned and a new top tank. should be 230-300

they take it out, take it apart, clean out all the crap etc. good as new. a new OEM or nismo thermostat is a good idea at the same time. The generic ones are very flimsy in comparision. nissan is ~50$ trade price. 82deg where the nismo is 72deg

Edited by RB_Ryan

You can easily mod the engine fan to pull more air and not have it locked on. They lose some of the silicon oil thats inside the fan hub over time. You can drill holes and refill them. Mine was doing the same thing although i would check the basics first and change the thermostat if it has been a while.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Did you panel beat the dents or have you tried to repair this only using filler?  Is your sanding block soft/flexible and is following the shape of the panel rather then just knocking down the high points? 
    • I haven't knocked them down yet. I think I made the repair more complex than it should have been. I had rock chips combined with waviness and dents and I tackled it all in one because it was near each other and just end up wasting a bunch of bog lol. I'll knock down those areas and see how I go. And yep what you are saying at the end is correct. I think I might be sanding the top of a steep hill then my sanding block falls into the dent and gets rid of the guidecoat if that makes sense. Though shouldnt unless I'm covering too big of an area with not a long enough block. I'll try something new and provide some updates. Getting there though! Thanks as always.  
    • Yeah makes sense, hard to comment on your situation without seeing what your doing. I was talking generally before, I would not be looking to randomly create low spots with a hammer to then have to fill them.  It's hard without seeing what your doing, it sounds like you are using the guide coat to identify low spots, as you're saying the panel is still wavy. I don't see how you're not ending up with patches of guide coat remaining in a wavy panel? Once the high spots are knocked down to the correct level, surely to have a wavy panel you need low spots. And those low spots would have guide coat still in them?
    • So I'll put filler past the repair area a bit to make sure I don't miss anything. Then I'll block it until it's almost level, put the guidecoat, then keep blocking until it's gone. Then it's still wavy.  In regards to hitting the panel, I saw this video might give more context - Skip to 0:47 he knocks it down. But yeah I'm sanding until the guidecoat is gone then checking because otherwise my filler is still well above the bodyline. Unless what you're saying is I should put guidecoat around it early, surrounding the filler then stip once it's gone?
    • I refreshed the OEM injectors with the kit and connected it up. It now ideals okay even with the IACV removed. Driving still has the same cutoff issue like the 550cc injectors so the issue is somewhere else. I bought FPG's Fuel Pump Hanger. I will be installing it next, but it is not as straightforward as I thought it was with my limited wiring knowledge and no instruction on the specific model I purchased (FPG-089). I also got the incorrect billet clamp as I could not find info on the OEM sizing.
×
×
  • Create New...