Jump to content
SAU Community

Recommended Posts

just to add a little to what Ben has already posted,

- none of the R32, R33 or R34 range shares the same part number.

- none of the S13, S14 or S15 range shares the same part number.

- A31 cefiro is also no good.

- Z32 300ZX no good either.

- autech stagea rear cradle number is 55400 - 0V600

i also check a few of the other jap nissans, like C34, C33, A32, Y34, Y33 etc and got no joy there either.

i wouldn't completely write them off though, the part numbers could just mean minor variations and not that they won't bolt up at all

if you have time, test some different ones out and let us know :P

this is an s15 rear cradle in a rwd s2 (i'd imagine cradle mounting points would be identicle on all wc34's so should fit them all)

s15cradle.jpg

they are meant to be ~50mm narrower than auto stag rear cradles (so similar width to 260rs cradle) but i'll get a mate to do some quick meausrements at his work if he has time (import wreckers) and post up what he finds between cradles if he can. keeping in mind a narrower cradle will need shorter half shafts and prob s14/15 swaybar too

like i said earlier, this is my own research so don't take my word - look into it yourself before you go buying anything. i plan to try out the s14/15 rear cradle for myself at the end of the year :laugh:

I sold a Stagea subframe to a guy wanting a wider track in a 180 (is that an S15?) so I would guess that an S15 would be no good. I suspect that any other Stagea subframe would do (pay to have a look and take a few measurements) but still vote for the weld/repair.

I sold a Stagea subframe to a guy wanting a wider track in a 180 (is that an S15?) so I would guess that an S15 would be no good. I suspect that any other Stagea subframe would do (pay to have a look and take a few measurements) but still vote for the weld/repair.

s15 is no good? the pic i posted up there IS an s15 subframe. the bloke you sold yours to would have needed offset bushes for the stag frame to bolt up to his s13 chassis, the same as you need when fitting an s14/15 frame into s13 (because s14/15 and wc34 have the same mounting points)

most of you would probably remember grant? here is his first hand experience of fitting an s14 subframe into his stagea http://www.skylinesaustralia.com/forums/Sp...ng-t216144.html

this might help, little example first. off topic.

i have severe strut tower rust. i email a few restoration joints with pics, even went into a few, and they all said they couldn't help, but yet they deal with cars that have about 95%rust all over :P

then i took it to my stepfathers mates work shop. got him to have a look, bang gave me a set price for minor and worst case. . . and is happy to give it a crack. should be going in towards end of the month.

35yrs on the job and still going, must be doing a good job at that

he might be worth giving a ring, just to see if he would consider fixing a subframe.

Phone: (03) 9701 6098 | Address: 78 Popes Road Town: Keysborough (south east Melbourne)

thanks for everyone's help... Fortunately Chasers in West Melbourne did a great job and managed to repair the subframe on the car, saving me a whole heap of money and effort.

Car drives so much better now. Will still be fitting the new bilsteins and whiteline bushes when I get a chance though. :-)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...