Jump to content
SAU Community

Recommended Posts

Hey Guys

Heres the story after 10 mins of driving and i come to a set of lights feels like my car has a heart beat or a pulse the revs go down then back up again. keeps on doing this. Feels like its going to just die on me do u know what is probally the cause of this???? i was thinking the fuel pump??? has any of you guys had this problem its 96 r33 srs2 N/A. and if so is it expensive to fix.

Link to comment
https://www.sau.com.au/forums/topic/282798-car-revs-drop-and-come-back-up/
Share on other sites

Get the fuel pump tested, you can test for fuel pressure and flow. Sounds more like you have a 'clean' problem to me, dirty plugs or sensor [o2,tps etc] somewhere.

Don't replace the fuel pump without testing the whole fuel system. Cost, sub $200, probably what ever a service is worth.

Fuel pump, being an N/A, a Walbro will do it easy, around $250 fitted, but get it checked first.

And get your fuel filter cleaned/replaced, could have dirt/water in it.

yeh i changed all of my spark plugs and replaced the fuel filter which was dirty as and still having the same problem? so im guessing would it be just the fuel pump or coil packs? and whats the o2,tps as you quoted????

atmo bov?

if u have a standard ecu try ressetting it (unplug battery and pump the brakes or turn stuff on and off to drain all the residual power from the wires) then plug battery bak in

easy thing to do and doesnt cost anything

if not start looking elsewhere

Hey mate, I think I'm having exactly the problem you are. I posted about it, it's only like the 10th post down lol... still haven't solved it though. There's a link to my youtube video of it as well, have a listen and let me know if the noise is the same.

Happens when my car is idle, warmed up.

My mechanic has told me my AAC valve needs replacing so I'm waiting for someone else to verify that this could be causing this noise? If so, then it could very well be your problem too.

CLICK HERE LINK OMG CLICK CLICK <== Link to my post, containing youtube link.

yes, most lumpy idles are caused by either the AAC or IAC. mostly the IAC (idle air control). this will happen when you put your foot on the clutch and it idles like a drag car. do a search on here, it has been covered many times before. it is reasonably easy to do. all you need is some carby cleaner and (from memory) a 12mm spanner. the IAC is situated on the back of the plenum near the firewall.

my car did this.

i had a power FC and it happened when i turned the air con on, and it happened randomly - not all the time.

could be completely unrelated to your problem, but when i turned the air on - revs dropped to about 300 and then it kicked itself back up to 1000, then dropped back down - kicked itself back up - etc.

was a power FC setting problem.

Check: IAC or AAC ( by that I mean clean it out) couple of bolts and some time with petrol or carby cleaner.

AFM. Clean with electrical cleaning spray. I think around $10 so just spray it into the AFM, no need to remove.

If you have a BOV other than standard or GTR then remove it.

Drive the car and see if it does it when you back off in gear then put it in neutral or if you are cruising along and suddenly push the clutch in. Won't be the coils as they would be acting up under boost before they played up at idle.

Always start with the simplest things first.

Ok can someone explain the difference between the IAC and AAC? By the difference, I really mean where both are located? I thought I'd had a go at removing the AAC from the back of the plenum... is that the right one? So where abouts is the IAC?

I always (stupidly) thought they were the same thing..... d'oh!

IAC and AAC are located very close to each other. if i remember correctly, the IAC is located above the AAC. IAC = easy to get to. AAC = not so easy to get to. i will have a flick through my workshop manual and see if it has any pics

IAC and AAC are located very close to each other. if i remember correctly, the IAC is located above the AAC. IAC = easy to get to. AAC = not so easy to get to. i will have a flick through my workshop manual and see if it has any pics

Could the AAC cause boost spike?? If it was failing?? I am working on an R33 at the moment and it seems to idle rough on and off. Get it idling smooth then 10 minutes later its idling like balls.....along with the rough idle I also have intermittent idle hunting after boost. Comes down to almost stall and then picks up again. Does it about 2 times then idle sets again. So couldthe AAC be a possibility?? when I say boost spike too I mean I get alot of lag then all of a sudden a major boost. Very hard to control and very unpredictable.

Could the AAC cause boost spike?? If it was failing?? I am working on an R33 at the moment and it seems to idle rough on and off. Get it idling smooth then 10 minutes later its idling like balls.....along with the rough idle I also have intermittent idle hunting after boost. Comes down to almost stall and then picks up again. Does it about 2 times then idle sets again. So couldthe AAC be a possibility?? when I say boost spike too I mean I get alot of lag then all of a sudden a major boost. Very hard to control and very unpredictable.

the AAC shouldn't affect boost at all. it only lets in a tiny amount of air. it could be causing the hunting idle after boost but there could be other causes too. when i first got my 33 it was pretty much stock, but if you gave it the beans then lifted off it would nearly stall. it was caused by worn spark plugs. if you have an atmo bov this can be made worse. i only had the stock bov though, so it isn't just atmo bovs that can make this happen if the plugs are crappy. what happens is that when you lift off and the bov opens, with an atmo bov all the air in the cooler piping is released out into the engine bay and this sucks a bit more air through the afm so the ecu puts more fuel in, making it too rich and the spark plugs aren't able to ignite all the fuel. with the stock bov a similar thing happens although it doesn't suck as much air through the afm, but you get some of the air that is being recirculated passing back out the afm, and since it doesn't know which way the air is travelling it dumps in extra fuel also. the fact that your idle drops after lifting off then comes good again makes me think that your problem is like mine and there is a very good chance that new plugs should fix it. and if you haven't replaced your plugs in a while it wouldn't hurt doing it anyway since it will only cost you about $30 for a set of plugs. the part number you want is BCPR6ES. don't bother with iridiums. i was getting similar life from copper plugs as from iridiums with a $100 price difference.

as for the lag, don't really know about that one. that could be caused by a lot of things. could be to do with the wastegate or the boost controller.

as for the AAC valve location, i looked it up again (it's been about 3 years since i had my 33 so i'm a bit rusty on locations of things). the AAC is attached to the side of the IAC. if you look at the back of the plenum you will see a round cylinder about 1 inch wide pointing towards the passenger side with a plug on it, and just behind it what looks like a really long nut with a plug in the end of it. the round cylinder is the AAC solenoid. the other is the IAC. you remove the whole unit with 3 bolts (i think they are 12mm, maybe 13mm) and 1 or 2 of them are located under the unit. then disconnect the plugs and hoses. the AAC i think is held on by 2 small phillips head screws. give the whole unit a good spray with carby/throttle body cleaner. then stick it back together and install the unit back in the car. after doing this it is best to readjust the idle which you need to lock the car into base idle mode. this can be done without a consult but i can't remember how. has something to do with bridging 2 wires in the consult plug.

Too late for the irridiums. Replaced with platinum plugs gapped at .6mm and new Yellow Jacket coils. AFM has been cleaned and a million other things have been tried.

I have a feeling that the lagging, idling, and boost spike are all to do with the same thing. I am doubtful that there is more than one issue causing these issues. The ECU is a Garage Saurus complete replacement plugin. Unfortunately no one here in Perth knows anything about the Garage Saurus gear. As in no body knows how to access the ecu to re map. I have a feeling thats what it needs.....

Thanks for your help anyway. I will have a look at a few more things. Do you know of anyone anywhere in australia that I could call to pick brains?? I have called most performance places here in Perth.....they all say the same thing, get a Power FC.....but I am not confident on spend $1500 on a Power FC until I know that the turbo or motor aren't shagged. Low compression can cause rough base idle.....yet to do a compression test. Pffft.....stupid R33!! Goes hard but this is frustrating!! :huh:

atmo bov?

if u have a standard ecu try ressetting it (unplug battery and pump the brakes or turn stuff on and off to drain all the residual power from the wires) then plug battery bak in

easy thing to do and doesnt cost anything

if not start looking elsewhere

I'll have to give that a go, mine has been doing it and it has an atmos + plumb back bov.

My car is known to die though while driving but only when braking quickly after a boot.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • GCG is a good company, they're a major distributor for Garrett in Japan as well.
    • Nah, OEM washer bottle and brake fluid reservoirs are fine I don't know what it is with the plastic that Mazda used, some plastics, like the washer bottle and brake fluid res are fine, and still look new after 20 years use, where as the coolant expansion tank, and PS reservoir, that I replaced with new OEM items when I first got the car, turned yellow and started getting brittle a few years later If the dirty yellow stained plastics didn't trigger me there wouldn't be an issue, but they did, much like the battery bracket....... Meh As for going back to work full time to support car stuff, nope, why, because I own a Mazda NC MX5, not a Nissan R series Skyline 🤣
    • I've never heard of CJ-motor, so can't advise you on them. I'd just go straight to GCG for a GCG highflow though. Seems no point to use a middleman. I'm somewhat surprised that the price on the CJ site is lower than the GCG retail price. Even though CJ would get a discount of some sort, you would hardly expect them to give up so much margin. Maybe the price is out of date? Having said that "I'd go to GCG"...when I did my highflow, I went to Hypergear. I did this https://hypergearturbos.com/product/rb25dethighflow/#tab-dyno-results with the R34 OP6 450HP profile. With the BB centre (extra $400) and intially with the standard boost actuator, but I eventually got him to send me the high pressure one when I got to the point of being able to actually use it. Ends up costing the same sort of money as the GCG highflow, but this is, of course, the turbo that I KNOW has a shorter length core and so moves the comp cover rearwards. The GCG apparently doesn't do that. My mechanic also swears by the GCG highflow, given that we have another turbo rebuilder who does something essentialy the same as theirs, using Garrett wheels. He says it stands up at really low revs and makes good power. I haven't pushed my HG highflow past ~240-250rwkW yet (should have a little more in it, but unclear how much) and it does have a fairly gentle boost ramp. OK, it's much better now that I have gotten my boost controller tuned up on it.  A lot of my earlier unhappiness was because I couldn't keep the wastegate flap as closed as it needed to be (including some mechanical issues). I'd still prefer it to boost up nearly as quickly as the stocker, and it certainly a bit slower than that. So maybe the GCG one is worth the first look (for you).
    • Ok thanks 🙂 I will higly consider this. Any "known" company for a good reviews and experience to send that off? Is that CJ-motor good one? Or go straight to GCG site? I need to use VPN to even find some of those "shops" let alone access them 🙂 
    • You can literally put in as much WMI as it takes to quench the combustion totally (and then back it off a little, obviously), and it will keep making more and more power. The power comes from the cooling effect of the water (and the meth) and the extra fuel (the meth, which also has massive octane). It is effectively exactly like running E85. One might be slightly better than the other, but they are damn close. But with either you can lean on the boost or the timing (or both) waaaay more than with just petrol and the results are similar. Here's the first thing I googled for an anecdotal bit of evidence. Can't access the attachment without being a gold member, but it is there for the getting if able to, or searched up elsewise perhaps. https://www.hpacademy.com/forum/general-tuning-discussion/show/wmi-vs-e85/
×
×
  • Create New...