Jump to content
SAU Community

Recommended Posts

  • Replies 49
  • Created
  • Last Reply

Top Posters In This Topic

I can get a fading transformer to light up a neon made up to size to fit in there. im not sure on price but if anyone is interested ill call around and see what i can arrange.

rembering i sell REAL neon so its 50times brighter than LED's and AEPRO autobarn stuff. problem is its glass and will need some TLC to install it in there so it doesnt break. But it would be a good effect.

Well,I am not all too familiar with the sanding of the back part yet but ,I once tried it with a Dremel and it was taking the paint off with out putting a hole through it just gotta keep it a nice and easy and be sure not to push down on it because you`ll just cut right through it FUNKMONKEY THE KNIGHT RIDER LIVES HAHA

I tryed to find out about how bright neon is and no one can tell me.

the best way to describe it is that the thicker the tube the duller the light

hungry jacks is 15mm red neon i have some 9mm red neon here. and if u turn it on in darkness u can not look at the tube for too long as it hurts your eyes.

thats the best way i can tell u how bright it is. if u put a mirror or something to reflect the neon behind it it will double in brightness (rubbs my eyes from the testing i have done this morning)

HEY PPLZ!!!! i just complete the first few stages on my badge for a 33... but i'm stuck on there lighting

i have pics on where i'm up too...

but yeah the lights i went to jay car... 30cm is just too damm short!!! it either a 'S' or a 'E' i'm missing... ahehae so yeah i don't know where to get a light...

also the hole i have made to put the light in is quite small.. just enough to fit a 5mm diameter cathode tube or sumthing of that name.. and the light it produces doesn't cover the "SKYLINE" work properly its like its too thin and yeah need some help...

One resistor per LED, any good electronics store will give you what you need, like Jaycar and then hook up to the 12 Volt park light circuit (numberplate wiring is good) and all you need to do is get some plastic or thin MDF or aluminium for a backing and drill 6mm holes to mount your LED's :wizard: Hey presto

auto trust: sounds good enough.. but ill see how good i go... but yeah its goin back on to the car first 2moro.. when i get time ill get it off again.. or when i have built my led Light show...

funky: that red translucent plastic thing i got from a sign writer they didn't have any that sticks so yeah i just cut it and slipped it in.. gonna stick it down sometime soon.. but yeah its just so i get a red lighting..

You know what would look cool.

i work at a lazercutting place and operate a lasercutter. i could cut the word SKYLINE out of 3m or 2m clear perspex rectangle so its the same size as the one of the back of all 33 or 32 skylines. then you could 2pak paint the perspex or sumthing. i dunno just an idea ? i could cut the word out to say anything the number plate of a car GODZILA anything really. but its getting late and it probabaly doesnt make sence lol.

:headspin: :headspin: :headspin: :headspin: :headspin:

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...