Jump to content
SAU Community

Recommended Posts

Hey Guys.

Was working on my R33 GTS-T Series 2. Put in new plugs. and now the car has never run the same.

I replace the plugs as the car was unstabe under heavy throttle loads.

I put it back together and its running like a WRX.

After this tho....

I bought new CoilPacks, and new plugs again... and gapped them. and changed the fuel filter.

AND it is still running like a shitbucket wrx. tested crank angle sensor and engin compression ratio, and also fuel pressure.

Any Help.

Next step is to have a look at the injectors.

Any suggestions before i take my car to bits?????

Cheers,

Michael

1. whats plugs did u put in? (list the model number and brand please)

2. what gap did you set them too?

gotta feeling you have used the wrong plugs and or at the wrong gap...

could also be an earthing issue, but lets eliminate these items one at a time first...

make sure you have them clipped into the clips properly (i had to use a flat blade screw driver to lever up the plastic tags to clip mine in properly) also i've been told if you've degreased your engine or something lately over the rocket cover that the oil/crap can fall down and short your plugs or some shit.

but its most likely your coils or you've f**ked the gap up

Used standard NGK plugs Part no. PFR5G-11

Gapped at .8

And the coilpacks are brand new. and the resistance has been tested also... all showing up fine.

The problem started when i took the old plugs out. And after replacing everything plug and coilwise its still not running properly. So far 3 sets of plugs.... and counting.

the car also seems to be running rather lean..

But still sounds like its not getting enough fuel or spark or something.

Hamdog.

What do you mean about clipping them into place???? My mechanic mate is doin all the work for me as he owns an R32. So things are pretty much simular.

You say you changed the coils - were they Splitfires or similar, or 2nd-hand stockers? If the latter, it's very possible that one or more of the coils you've swapped on aren't working properly. If it is indeed running lean as you say though (measured, or guessed?), maybe you bumped an injector plug or crimped a line to the fuel filter or something, who knows. The timing might be out too, did you knock the plug on the CAS (front of the engine)? Stuffed AFM/plug? Plastic still on the fuel filter (have seen that before lol)

Does it have a consistent miss at idle? If so, assuming it's a spark issue, pull the plugs one by one and see if any are wet. If they are then your injectors are probably working fine and you've identified the cylinder/cylinders that isn't/aren't firing. Then it's a process of elimination... swap coils around and see if the problem moves with a coil for example, or whether it stays on a given cylinder, swap plugs around, check connectors, clips, earth straps, coil loom, AFM etc. If all else fails, grab a mate with a working S1.5/S2 33 and swap parts until yours runs properly and work it out from there.

Also, IIRC 6s are the stock heat range for plugs. I used to use BCPR6ES, they're coppers and are pretty cheap and did the trick nicely.

Hamdog.

What do you mean about clipping them into place???? My mechanic mate is doin all the work for me as he owns an R32. So things are pretty much simular.

when i changed my coilpacks, i didnt clip the loom/wiring harness into one of the coilpacks properly and after a while it wiggled free and lost connection. therefore a cylinder stop firing

took me ages to realize what i'd done wrong and i just got a flat blade and clipped the tag into it properly.

also check your afm plug ect

i was gonna say have a look at the wiring for the coils, there are chances that some of the wires are broken and earthing, or that the insides of the plug for the coil is not connecting, i had the same thing, but it tunred out to be my sticky injectors.

Normally if it is a plug issue it will be around the 3500 - 4000rpm mark, it will start sounding like a WRX.

If that is the case BKR6E which is a v-power plug or like the one mentioned by Revhead the BCPR6ES will do the job.

Yeah it will def depend on whether the coil packs are bran new or second hand. And usually they will start off ok until they get hot then they start to break down. Try removing one coil pack at a time with the engine running and see which one has no effect when removed. The ones that are working will affect the engines idol when removed the bad one/'s won't. My experience with AFM's is usually they just stop working full stop and thus the engine doesn't run at all. I had one go on my R33 GTR and the engine just died. May be worth checking the igniter unit? I don't know anything about those sorry.

Mate good luck and let us know what the problem was when you solve it.

Hi guys...sort of having a similar problem with my series 1 r33...the car started backfiring about 150km ago, but only under heavy throttle as the car still runs fine at 3500-4500 rpm...it only seems to be when the car is at high boost. The car idles fine and spools without problems, however as soon as i put my foot to the floor and it gets to 14psi it backfires heavily. The oil has been changed under 500km ago and there are no oil leaks and no smoke coming from the exhaust (which i hope to rule out turbo problems). My mate seems to think its def a fuel problem so I changed the plugs on wednesday (put ridiums in and didnt change the gab at all. The plugs are all connected properly to aviod 1 unclipping but :blush: im pretty sure the ridium's have made it worse. Replaced the AFM and even the O2 sensor and still nothing. About to change the plugs again to NGK BKR6E's and see if that makes a difference, but from what I can gather from the reply's above i think my coilpacks are f&*ked. Any ideas before i go out and buy new coilpacks only to find that it may not fix my problem or would i be able to get away with second-hand ones?

Cheers

Brendan


Hi guys...sort of having a similar problem with my series 1 r33...the car started backfiring about 150km ago, but only under heavy throttle as the car still runs fine at 3500-4500 rpm...it only seems to be when the car is at high boost. The car idles fine and spools without problems, however as soon as i put my foot to the floor and it gets to 14psi it backfires heavily. The oil has been changed under 500km ago and there are no oil leaks and no smoke coming from the exhaust (which i hope to rule out turbo problems). My mate seems to think its def a fuel problem so I changed the plugs on wednesday (put ridiums in and didnt change the gab at all. The plugs are all connected properly to aviod 1 unclipping but :yes: im pretty sure the ridium's have made it worse. Replaced the AFM and even the O2 sensor and still nothing. About to change the plugs again to NGK BKR6E's and see if that makes a difference, but from what I can gather from the reply's above i think my coilpacks are f&*ked. Any ideas before i go out and buy new coilpacks only to find that it may not fix my problem or would i be able to get away with second-hand ones?

Cheers

Brendan

I suggest you find someone with the same engine that is running well and swap coil packs for a test. Go for a 5 to 10min drive getting up and over(if possible) the trouble spot and if it runs better than you can safely spend the money on some new coil packs. Also get a gap gauge and re-gap your plugs to .07 which ever plugs you use. If possible use the recommended ones for your model not a referred one unless you've got some serious hp. You'd be surprised at how heat numbers and different types of plugs have an effect on the cars performance.

Mate good luck too.

Edited by shaggy_76
  • 4 weeks later...

Myr33GTS-T try your ignition module it could be stuffed as this was my problem when my car sounded like a wrx haha and shaggy pretty sure it would be the coils as a mate has the exact same problem.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Even more fun, leave all the ADAS stuff plugged in, but in different locations, hopefully avoid any codes!   And honestly, all these new cars with their weird electronics. Pull all the electronics out Duncan, and just shove an aftermarket ECU and if needed a trans controller in, along with a PDM. Make it run basic but race car styled!
    • To follow up a question from earlier too since I had the front bar off again (fking!) This is what is between the bumper and the drivers side wheel And this is the navigator side, only one thing but its a biggy! So basically....no putting coolers in the wheel arches without a lot of moving other stuff. Assuming I move to properly race prepping this car I'll take that job on and see how the computers respond to removing a whole bunch of ADAS modules
    • So I prepped the car for another track day on Wednesday (will be interesting to see coolant temps post flushing out and the larger reservoir, with a forecast of 3-14 being 20o cooler than last time I took it out). Couple of things to mention; since I am just driving the car and not taking a support vehicle, I took the rear seats out and just loaded the back up Team Trackday style. Look at all that space! To cover off removing the rear seat....it is weird (note the hybrid is probably different because it wouldn't have folding rear seats) Basically, you remove the lower seat base, very similar to a r series but it is a clip that pulls forward to release the base rather than it being bolted down. Easy Then, you need to remove the side section of the rear seat on each side. There is a 14mm head nut at the bottom of the side piece, the it slides upwards off a hook at the top to release; you also need to unhook the seatbelt from the loop at the top. Then the centre piece is weird. You need to release/fold the seats forward with the tab in the boot on each side From there, there are 2,x12mm headed bolts holding the rear of each seat to the folding bracket, under the trim between the rear seat and the boot (4x christmas tree clips there, they suck). The seat is out but you can see where the bolts attach to the bracket
    • As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
×
×
  • Create New...