Jump to content
SAU Community

Recommended Posts

Yes they fit a r31

brake deflectors. Laser cut alloy, professionally folded and Tig welded and Powder Coated.

Stainless cable ties to secure to radius rods and button head Allen Key bolts and nuts to secure to the lower control arms. Fits all Nissans other than GTiR and GTR.

$190 retail for the kit FATZ price $150.[/b]

DSCF8153.jpg

DSCF8159.jpg

I have a similar set on my gtr they roc(if you want on for your gtr I can get them as well)

Basically they cool the brakes more which in turn makes your pads last longer

Johnny has tested them and they reduced the rotor temp by 150 degrees

I used them at the philip island 6 hour race and they made a large difference to pad life and the brakes didn’t fade

Group buy will go for the next two months but get in now and ill have them off asap ( eg I should have the first delivery tomorrow)

Lets say 20 delivery throughout Australia

Bank details

Peter carruthers

Acc number 428 965 807

Bsb 112-879

Please once you deposit cash call me on 0448468884 and tell me you have.. then pm me with your address, name and mobile phone number. Just makes tracking easier

Note when you put them on depending on the offset of your rims they may scrub a little at full lock) this happens on cars that when at full lock you rims rub on your lower arm. This is quite common and I had to chop a few chunks out to clear the rim and rubber

Either way they fit nicely however be aware that they may scrub a tad at full lock

So basically no really good if you’re a latte drinking carpark driver… however if you hit the track heaps they rock!!!

Pics of the gtr specific ones on my car

deflector2.jpg

deflectors.jpg

just double checked with johnny and its 20 deliver but and 150 for the deflectors

keep it real!

Link to comment
https://www.sau.com.au/forums/topic/284424-brake-air-deflectors-150/
Share on other sites

I've got the GTR ones on my R32 GTR and they work a treat, they did require alittle modification with a angle grinder (check uploaded pic) but otherwise I can full lock both ways without scraping my wheels (stock 16" gtr wheels with 225's) on them. Just a word of advice when you get to fitting these, GTR's radius rod are bent straight out the factory, to accommodate the GTR wheels so don't stress over them being bent.

post-51527-1251607651_thumb.jpg

  • 4 weeks later...
  • 3 weeks later...
still available? and any point for the average track punter? (ie, 2-3 times a year)

Definitely worth it, will extend life of rotors and pads, and help prevent the brake fluid boiling.. nothing worse than going off the track when the brake pedal is pressed to the firewall.

  • 1 month later...

No. I was contacted by unique and they said they weren't making the gtr ones for a couple of months, supposedly theres meant to be a refund organised but I haven't heard since.

  • 1 month later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • looking for some help and maybe some insight on others experience with a new LSD. R34 GT ran and drive beautifully, but always alot of grip loss due to the open R200 rear end, so I just installed a new 1.5 LSD way into the stock open R200 for a ER34. Simple. Everything seemed right. I test drove for the first time this weekend. as I started to back out the garage the first time slowly with tires straight it sounded and felt like I had a loose or half disconnected drive shaft...that was clucking around loose and shaking entire vehicle, and making it feel like the trans clutch was spontaneously slipping then grabbing very roughly while just letting out pedal slowly. I backed it out went to pull forward with the same noise, shake and slip grab feeling with hesitation, I turned the tires to back out more and then pulled ahead some same thing but worst because of added wheel resistance (which that I expected) puzzled … pulling it back in checking everything over and finding nothing wrong, I tried it the next day. same thing, couldn’t believe how it shook everything again making a terrible noise and making it feel like the trans clutch was slipping and grabbing, but I got it out of garage into the driveway, got it straight, drove forward and then reveres a few times in a straight line everything shaking , causing what felt like clutch slip and grab every time, sounded like right behind front driver tire and I could feel it in the floor board with my feet,... worst right when beginning to let clutch pedal out to engage slightly, shuttering and sounding terrible along the way…I managed to slowly get down the road, babying it the whole way, once I was rolling (out of 1st) seemed to be better and between shifts, then clutch felt closer to normal…not slip/ grab etc., but back down to any stop, straight road or turning, same thing. Made no difference if all tires were straight or if I was turning. All other gauge read out correct. with in 2 miles as planned I reached the empty parking lot and performed the break in procedure that came with lsd, essentially to drive in a figure 8 a bunch.  Did this, binding chattering, and shaking the car the whole way. I drove it back home seemed somewhat normal once I was in straight line and past 10 mph or so, and I know it will “bind” on corners and cause some tires squeal when turning especially from a stop, but when I begin to move it still causes what feels like the trans clutch to slip and jerk badly as well as shaking the entire car, and sounds terrible, that I didn’t expect. I used the fluid they supplied with LSD kit and did the breaking, planning to change fluid as they suggest after breaking, but wondering will it get smoother or less aggressive with use? maybe a 1.5 is just too aggressive for normal road driving?   I have a LSD that I put in my 71 cuda when I restored it, with amazing smooth , quite yet effective results. Different style LSD but that ones a joy to drive. maybe expecting too much from this R200?
    • Join SAU NSW for a flame-grilled feed & flame-spitting cruise! Sunday 17th August 2025 3:30PM Meeting Archies Flame Grille Sylvania Waters 4:45PM Cruise Departure 5:15PM Arrival at Cape Solander Kurnell Meet Location: Archies Flame Grille Final Destination: Cape Solander Kurnell *Disclaimer* There will be a lead and follow car so no one should get lost. If you would like to attend or bring others along please put your name down and a +1 as numbers will be needed prior! This is NOT a race and we will all be adhering to all road rules. If this is what you want please come to one of our many track days. This is an official SAU:NSW event and will be run under a CAMS permit. One of the things that really sets our club apart is our commitment to being true enthusiasts. When on normal roads we strive to maintain good relations with the authorities as well as the public in general. When attending one of Skylines Australia NSW events please try to: • Be aware of surrounding environment and act accordingly. • Drive courteously on the state’s roads as a true enthusiast should. • Understand how important it is to maintain the good name of SAU NSW and thus, treat others accordingly. • Any misbehavior will not be tolerated and you will be asked to leave.
    • Yeah good luck out there! Will be good to see a mighty GTST going harder than the GTRs
    • i will be there 😁
    • Hello!  i just finished manual swaping my r34 skyline with a r33 rb20de box(RB71C)box  When the car is running it squeaks crazy loud and it was smoking from the gearbox area. The gearbox is fine it was tested. The clutch slave cylinder seems like it doesn't fully releases the clutch. I want to ask if this noise is from the throw out bearing or could it be the clutch assembly or disk att.xFliq87Gzw6kImKBVqDebXkj0fBqymk0JaYeP3_3SlM.mp4
×
×
  • Create New...