Jump to content
SAU Community

Recommended Posts

ey fellas

need some advice, i wanna build a hybrid motor with an RB30 bottom end with either a RB25 or RB26 head. the dilema im having is trying to find out which head will bolt straight on with the least amount of modifications? ive read some of the threads on RB30 conversions but still cant find one that will answer my question

cheers

Link to comment
https://www.sau.com.au/forums/topic/285088-need-some-help/
Share on other sites

Theres an rb30 sub-forum in the force induction forum

rb26 is a direct bolt on but the block will need to be tapped out to take the 12mm headstuds

rb25 needs an oilfeed for the vct uses 11mm studs and are a direct fit to the block rb30 is 11mm (head needs a lil modding)

plus side is rb26 has a much better looking plenum however if its going into a gtst it will cost alot for custom piping (easily 2-3k) if u opt for a forward facing plenum

i think cubes has a rb25/30 with a low mount on the stock manifold with 400hp

the rb26 can mount a pair of -10s onto the stock manifolds (see Marko R1s thread)

Link to comment
https://www.sau.com.au/forums/topic/285088-need-some-help/#findComment-4788626
Share on other sites

The head Ryan is talking about (R32 RB25DE) is the EASIEST head to use if replacing an RB20 as everything plugs back in and will run on the stock ecu (which you can then have remapped).

If you have any specific questions, feel free to shoot me a PM :P

Link to comment
https://www.sau.com.au/forums/topic/285088-need-some-help/#findComment-4789095
Share on other sites

Hey guys

Ive tried surfing the net but i cant find the appropriate information. I'm just wondering if any knows or has a link to a website or a picture that shows the timing belt assembly of an RB25/30DET motor?

Also ive been hearing that i may have to put a new tensioner onto the block for the timing belt to be able to go on?

Whats the best way to get a good compression ratio with good response out of this motor?

Is it better to use a RB25DE or RB25DET head for this kind of conversion for results in compression and response?

thanks

Edited by Morgz32
Link to comment
https://www.sau.com.au/forums/topic/285088-need-some-help/#findComment-4790765
Share on other sites

hi gtst v-spec i tried opening that file for the build but its a winzip format and i cannot open it or save it and then open it.. any other ideas or does someone have it that and would kindly send it to me??

thanks

Link to comment
https://www.sau.com.au/forums/topic/285088-need-some-help/#findComment-4790795
Share on other sites

Hey guys

Ive tried surfing the net but i cant find the appropriate information. I'm just wondering if any knows or has a link to a website or a picture that shows the timing belt assembly of an RB25/30DET motor?

Also ive been hearing that i may have to put a new tensioner onto the block for the timing belt to be able to go on?

Whats the best way to get a good compression ratio with good response out of this motor?

Is it better to use a RB25DE or RB25DET head for this kind of conversion for results in compression and response?

thanks

Yes you will need to tap a new location for the tensioner, should be in the build pdf I think.

What are you doing with the bottom end? forging it or leaving it standard?

Standard, you're better off with the 25DE head for compression reasons. If you're forging the bottom end then get some twincam 30 specific pistons and use the 25DET head.

Link to comment
https://www.sau.com.au/forums/topic/285088-need-some-help/#findComment-4791496
Share on other sites

hi gtst v-spec i tried opening that file for the build but its a winzip format and i cannot open it or save it and then open it.. any other ideas or does someone have it that and would kindly send it to me??

thanks

Here is the PDF File

rb30_dohc.pdf

Link to comment
https://www.sau.com.au/forums/topic/285088-need-some-help/#findComment-4791574
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I have been being VERY quiet about what you're alluding to, as it is something that ticks me off... The number of cars from factory that run coil overs is HUGE! Most of them these days do... The other part that annoys me, is people saying "Well all the incabin adjustable suspension is illegal by blah blah blah"... If that's the case, then why can I buy a car brand new that can do it if, FULL STOP in cabin adjustable suspension is illegal...   Also, I could just chuck some aftermarket shocks in my car, throw the stock springs on, after my blue slip, dump my super low springs back in. Same shock and spring style setup... Hell, they could also be the same colour springs etc.     I'm voting, BlueSlipper didn't want to touch the above car for some reason. Whether it be some sort of bias against the car, the owner, them maybe having previously done dodgy shit and now they're being super careful in case they get slapped in the face by the Gumbyment again... Find a new blueslip place.   And can confirm as you had said, yes there are holy bibles of vehicle heights, and all sorts of other suspension stuff. Heck your run of the mill mechanic, and tyre shop has access to all of that stuff. It's how they do wheel alignments...
    • Funny story Heading to Sydney this morning on the HWY there was some slow traffic, so I gave it the beans and midway through my overtaking "power run" I lost all power It seems that I missed a hose clamp,  and the MAF and filter went WiFi To make this more problematic, the little tool kit that lives in the boot, is sitting in the sun room at Goulburn......LOL Luckily for me I found a bit of steel on the side of the road that could be used like a rusty and bent flat head screw driver to tighten it up enough that it got me into Sydney, it is now all tight like a tiger with the aid of a 8mm socket Note to self: Use my brain and double check stuff, and always keep that little tool kit in the car for when I have a brain fart
    • Oh, and as for everyone with their fuel economy changes, I switch between E10 and 98 in the company car. Even do when I had personal cars that could run on E10. You know what changed my fuel economy in any noticeable way? How I drove, and where I drove. Otherwise, say on full tanks of just back and forth from work only (So same trips, same sort of traffic), couldn't notice a difference that I can correlate to the type of fuel in use. In the current vehicle, that's over 42L of USABLE fuel. While 98 is all "more energy dense", it also has higher knock resistance as it takes more energy to get it to ignite too. The longer hydrocarbons, typically more tightly bound. So running the same ignition map, can also produce less power, if there isn't enough time to get it all burnt through properly, as yep, the flame propagation speed is different from lower octane fuel to higher (Higher has a lower flame propagation, due to the more tightly bound and harder to self ignite funs. This is also typically where, a vehicle that is designed purely to run on 91 (Whether it be E10 or normal 91) usually sees absolutely no real world difference in fuel economy for the normal man, woman, or dog.
    • We've got some servos around me that have 91 with E10, 91 (no E10), 95, and 98. At those stations the change from 91 E10 to 91, is typically around 8c/L.   But lets not get started on the price of fuel in Oz. It's ridiculous. All the service stations around me, bar one, the price of fuel has been over the $2 mark per litre for the cheapest, 98 being around $2.45. That one service station is a CostCo, fuel from it comes from the same refineries, and makes no pitstops, it runs great, including the 98. In fact, I've had no issues on CostCo fuel, but plenty of issues at other stations!. The CostCo fuel, was $1.65 roughly this week for 94 with E10. $1.88 for 98. Servos directly across from it, $2.10 for 91 E10, and $2.48 for 98. The part I had to laugh at? If I drive multiple HOURS away from Brisbane, say out near Nanango, or Kingaroy, or even out to Goondiwindi, the price of their fuel, is the same as what it is at the CostCo... Oh, and that BP servo at Goondiwindi is HUGE and goes through epic turnover of fuel, so it's not sitting there for weeks going to shit. And what blows me away, my mate is one of the people who drives the Fuel Tanker all around QLD, delivering to all those places. At the same company his previous role was doing the "local haul" deliveries... Same truck, same driver, same pickup point it all comes from. So you tell me, how the hell it is 60c/L CHEAPER for fuel, when nearly all else is equal, except they require a B-Double to drive half a day out of Brisbane, and half a day back, every second day, compared to the delivery that can be under 30 minutes drive from the fuel pickup point... Not to mention, go five blocks down the road, and Ampol to Ampol will vary 30c/L... And I've had this conversation with my mate... The way it's priced, is just typical, pure and utter rubbish... He also does runs from Brisbane, to all over QLD, down to Newcastle, Sydney, Nowra, Melbourne, Geelong, and even out to parts of the NT depending on the companies needs. His main stuff is all the longer distance away from home for a few days at a time, then when he's back, he loves to just pickup extra shifts wherever he can in whichever truck, hence all the weird different places.   Oh, as for getting E10 into all the fuels in Australia... It was very quickly highlighted, that we don't have enough biomass available to use to make E10 sustainably like they require, and it would dramatically cut into our, and the worlds food chain supply...   I vote we all just start running on liquid methane gas... Plenty of that just getting tapped off at tips from underground decay... (Note, this is pure just stupid commenting. I could very easily highlight the reasons its not a good idea especially on scale...)
    • Am I correct in assuming that the R35's are getting the classic skyline haircut off the odometer?  Quick search on carsales, there are 33 08 and 09 GTR's for sale, only 2 of them have more then 100,000km's on them (116,075 and 110,000 respectively).  And somehow there are about 25 for sale with around 60,000kms? Looks like the classic skyline haircut to me =/
×
×
  • Create New...