Jump to content
SAU Community

Recommended Posts

You need to remove the headlight and find the leak and seal it or else it's just going to reoccur.

As far as getting rid of what's in there, your best option is more than likely going to be to go for a night cruise so your headlights are on for enough time to evaporate the condensation that's in there.

  • 2 years later...

check on the top of the headlight, there should be a rubber seal near the indicator side, mine wasn't sealed properly as i can pry it out with my fingers and it exposes a hole to the insides, i believ this is where my headlights fog up/get cloudy from.

check on the top of the headlight, there should be a rubber seal near the indicator side, mine wasn't sealed properly as i can pry it out with my fingers and it exposes a hole to the insides, i believ this is where my headlights fog up/get cloudy from.

  • 2 weeks later...

My R34's headlights have been like this since I got it from import, but they seem to have a murky type of film on the inside of the glass. Does anybody know if the light housing and the glass separates? ...Is there a way of cleaning it out?

My R34's headlights have been like this since I got it from import, but they seem to have a murky type of film on the inside of the glass. Does anybody know if the light housing and the glass separates? ...Is there a way of cleaning it out?

It does, but you have to heat it up in an oven or with a heatgun to soften the sealer, then pry it apart. Depends how game you are.

  • 2 weeks later...

i did mine, a few times actually..:D

it wouldnt fit in my oven and i wouldnt recomend it anyway

what i did was buy a 20$ heat gun form bunnings..the you just keep running it all around the seal for 10 minutes or so with out getting to close to melt the light of course..just keep it moving and get all the silicon very warm..

Then when its all warm, concentrate on one end, the inside end (where the grill is) is best, warm it real hot then just hold the light between your feet and pry that end apart .do not try to pry the whole lot at once just do the end

When you have opened one end work your way around heating a section and pulling it apart..should take 3 or 4 turns and the whole cover will be off.

it really isnt too hard, but it takes patience, dont try force it apart, if the silicon is hot enough it will pry apart without too much effort..once the seal is cracked its easy

Too put it back together just reheat the silicon and stick it back together you don't really need to put new silicon in..

you can also use the heatgun to dry the condensation, but dont get too close..i made that mistake once and your light goes from fine too f**ked in about 3 second..

..im glad I read this thread cause its done it again so maybe its that little rubber hose causing my problems.. :thumbsup:

i did mine, a few times actually..:D

it wouldnt fit in my oven and i wouldnt recomend it anyway

what i did was buy a 20$ heat gun form bunnings..the you just keep running it all around the seal for 10 minutes or so with out getting to close to melt the light of course..just keep it moving and get all the silicon very warm..

Then when its all warm, concentrate on one end, the inside end (where the grill is) is best, warm it real hot then just hold the light between your feet and pry that end apart .do not try to pry the whole lot at once just do the end

When you have opened one end work your way around heating a section and pulling it apart..should take 3 or 4 turns and the whole cover will be off.

it really isnt too hard, but it takes patience, dont try force it apart, if the silicon is hot enough it will pry apart without too much effort..once the seal is cracked its easy

Too put it back together just reheat the silicon and stick it back together you don't really need to put new silicon in..

you can also use the heatgun to dry the condensation, but dont get too close..i made that mistake once and your light goes from fine too f**ked in about 3 second..

..im glad I read this thread cause its done it again so maybe its that little rubber hose causing my problems.. :thumbsup:

hmm sounds easy enough .. but knowing me, i'll probably heat the glass, pry it off, shatter everywhere and in my eyes lol

will defs be giving this a go though, cheers for the info Artz!

i did mine, a few times actually..:D

it wouldnt fit in my oven and i wouldnt recomend it anyway

what i did was buy a 20$ heat gun form bunnings..the you just keep running it all around the seal for 10 minutes or so with out getting to close to melt the light of course..just keep it moving and get all the silicon very warm..

Then when its all warm, concentrate on one end, the inside end (where the grill is) is best, warm it real hot then just hold the light between your feet and pry that end apart .do not try to pry the whole lot at once just do the end

When you have opened one end work your way around heating a section and pulling it apart..should take 3 or 4 turns and the whole cover will be off.

it really isnt too hard, but it takes patience, dont try force it apart, if the silicon is hot enough it will pry apart without too much effort..once the seal is cracked its easy

Too put it back together just reheat the silicon and stick it back together you don't really need to put new silicon in..

you can also use the heatgun to dry the condensation, but dont get too close..i made that mistake once and your light goes from fine too f**ked in about 3 second..

..im glad I read this thread cause its done it again so maybe its that little rubber hose causing my problems.. :thumbsup:

Thanx ARTZ, I'll swallow my fears of the unknown and have a go at it, might try to get some pix to post for everybody else

  • 3 weeks later...

I know a some people lights are real bad on the inside, but sometimes u might be suprised at how dirty/foggy the outsides are.

In my pic i left the bottom left corner dirty for you to see the difference, I clean mine once in a while with Autosol. comes up beautiful! Def worth a try before pulling things apart. It works good on foggy looking indicators too:)

IMG_2282.jpg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...