Jump to content
SAU Community

Recommended Posts

i have just installed a new alpine head unit in my R33 s2. the head unit works alright, but the clock on the dash seems to be resetting itself every time when i start my car. even my head unit pushes the cd out and is in off-mode every time i restart my car. the previous head unit was also an alpine. did i do something wrong with the installation? help needed.

i have just installed a new alpine head unit in my R33 s2. the head unit works alright, but the clock on the dash seems to be resetting itself every time when i start my car. even my head unit pushes the cd out and is in off-mode every time i restart my car. the previous head unit was also an alpine. did i do something wrong with the installation? help needed.

I'm guessing there is a "memory wire" (+) that should connect straight to the battery and not via the ignition...

usually yellow wire

i bet you connected memory (yellow) to power (red )

what headunit you have?

i had an alpine unit previously. so i bought a new alpine unit and connected the exact same wires to the new unit. yellow to yellow, etc. what should i do now?

  • 5 months later...

i know its a late post but im having the same dramas, but i know what the problem is but cant the the bloody fuse for the back up, where is it??? am i missing something, in my car tho everything resets, air con, clock, cd player

  • 3 weeks later...
pull them till you find a blown one. I can't remember placement in that panel.

i did this like 2 or 3 times, thats y im confused cause i cant find a blown fuse anywhere, i must be missing something, its driving me nuts

  • 2 weeks later...

Get a cable tester (little sharp point thing with the little light in it) and start going through your dash with the ignition off and find your constant power & ignition power cables and make sure you've wired up the head unit properly.

If it's affecting aircon, stereo & clock, then it would have to be a fuse.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yup. You can get creative and make a sort of "bracket" with cable ties. Put 2 around the sender with a third passing underneath them strapped down against the sender. Then that third one is able to be passed through some hole at right angles to the orientation of the sender. Or some variation on the theme. Yes.... ummm, with caveats? I mean, the sender is BSP and you would likely have AN stuff on the hose, so yes, there would be the adapter you mention. But the block end will either be 1/8 NPT if that thread is still OK in there, or you can drill and tap it out to 1/4 BSP or NPT and use appropriate adapter there. As it stands, your mention of 1/8 BSPT male seems... wrong for the 1/8 NPT female it has to go into. The hose will be better, because even with the bush, the mass of the sender will be "hanging" off a hard threaded connection and will add some stress/strain to that. It might fail in the future. The hose eliminates almost all such risk - but adds in several more threaded connections to leak from! It really should be tapered, but it looks very long in that photo with no taper visible. If you have it in hand you should be able to see if it tapered or not. There technically is no possibility of a mechanical seal with a parallel male in a parallel female, so it is hard to believe that it is parallel male, but weirder things have happened. Maybe it's meant to seat on some surface when screwed in on the original installation? Anyway, at that thread size, parallel in parallel, with tape and goop, will seal just fine.
    • How do you propose I cable tie this: To something securely? Is it really just a case of finding a couple of holes and ziptying it there so it never goes flying or starts dangling around, more or less? Then run a 1/8 BSP Female to [hose adapter of choice?/AN?] and then the opposing fitting at the bush-into-oil-block end? being the hose-into-realistically likely a 1/8 BSPT male) Is this going to provide any real benefit over using a stainless/steel 1/4 to 1/8 BSPT reducing bush? I am making the assumption the OEM sender is BSPT not BSPP/BSP
    • I fashioned a ramp out of a couple of pieces of 140x35 lumber, to get the bumper up slightly, and then one of these is what I use
    • I wouldn't worry about dissimilar metal corrosion, should you just buy/make a steel replacement. There will be thread tape and sealant compound between the metals. The few little spots where they touch each other will be deep inside the joint, unable to get wet. And the alloy block is much much larger than a small steel fitting, so there is plenty of "sacrificial" capacity there. Any bush you put in there will be dissimilar anyway. Either steel or brass. Maybe stainless. All of them are different to the other parts in the chain. But what I said above still applies.
    • You are all good then, I didn't realise the port was in a part you can (have!) remove. Just pull the broken part out, clean it and the threads should be fine. Yes, the whole point about remote mounting is it takes almost all of the vibration out via the flexible hose. You just need a convenient chassis point and a cable tie or 3.
×
×
  • Create New...