Jump to content
SAU Community

Recommended Posts

R33 GTS-T

Note: Both sparkplugs and coilpacks were replaced about 2000km ago and the car was running without fault before I started playing with the exhaust.

Been doing a bit of turbo-back exhaust modification lately, and after cracking the shits / returning to my original dump/front pipe, I'm now left with something of a rich and retard problem. It only happens high up in the rev range and only when giving it full throttle. Because of the wide open throttle thing, I suspect it's actuator or vacuum leak related. I haven't touched the vacuum hoses though. My wastegate flap was getting jammed by the aftermarket dump pipe after I installed it, could this have damaged the actuator diaphragm?

Another possibility I'd like to put forth: because the jammed wastegate flap caused my turbo to boost almost infinitely until boost cut when I had the aftermarket system on...I'm thinking the ECU has logged a fault code or something and because I haven't reset it (the thought to do so has only just occurred to me), so perhaps an ECU reset will fix this? Will try this tomorrow...

Interesting to note is that my engine under some conditions is still boosting past the normal .5 bar up to about .6 and sometimes .7 - this is where I notice most R&R occurring. Doesn't seem to be any R&R occurring at or below .5 bar.

Suggestions? I'm seriously regretting ever touching my exhaust system :(

Link to comment
https://www.sau.com.au/forums/topic/287419-rich-retard-high-in-the-rev-range/
Share on other sites

Its just the ecu's way of protecting the engine... when it sees too much airflow through the afm it will start to retard the timing and richen the mixture... you might have damaged the actuator making it open later which is causing it to R&R... even still just having an aftermarket exhaust on there can sometimes trigger R&R in the right conditions... it increases airflow through the whole system but you won't see it in a boost increase, the afm however does see the extra airflow...

when I first boosted my old car I used to get it a lot so I used a SAFC to trick the afm... even still on cold nights it would sometimes happen... best mod for them is a Power FC and good tune

also dump pipes don't make a huge difference... the exhaust housing on the stock turbo is where the restriction is, not much gain fitting a dump pipe (although people will tell you otherwise)

Yes a Power FC was my immediate thought for a solution lol. I will be heading down that track...but thought I'd try and diagnose the problem before this because it might not be directly ECU related and that will just make things hard for a tune.

I think I'll try fitting another actuator to it. What bugs me is I now have my original exhaust back on and it's still doing this shit, when it wasn't before with the original exhaust.

Cheers.

yeah that points to something being damaged... or something not being reinstalled correctly...

you could have also stumbled on a bad batch of fuel and the ecu is retarding the timing to protect the motor but that's a long shot

I don't like people saying to throw more mods at a problem but in the case of 33GTSt's they do really well with some a/m management and good tune... I mucked around with an SAFC for ages but should have just done it properly in the first place... they drive really nice with just a full exhaust and good tune... mid range picks up massively with a few more psi and a better cooler too

what are you actually feeling? is it missfiring or just getting sluggish? when i was hitting rich and retard in my 33 it wouldn't missfire or anything like that, it just killed the power for half a second then kicked back in.

if it is a missfire:

what series motor do you have? if it is a series 1 with the ignitor pack then that could be the issue since you have replaced coils and plugs.

No misfire as far as I know, it's a complete dead spot in the rev range. I say this because I can take the RPM all the way to 7000 without a problem, as long as I don't do it with full throttle.

It drives fine with 3/4 throttle applied (which incidentally keeps the boost just under .5 bar too). But if I go wide open throttle, at .5/.6/.7 bar the revs climb sort of jerky and power comes on and off, almost as if it's switching between on boost and off boost.

Farkin pain in the ass. I reset the ECU and I thought this fixed the problem but it appears to still be there. Gonna replace actuator (anyone got a spare?) and maybe dump pipe gasket...these are the only physical things I touched when playing with the exhaust, so unless it's one big coincidence, I don't see what else could be doing this.

0.7bar is only around 10psi so i wouldn't normally think that it would be hitting paris hilton (rich and retarded, LOL) at that boost level, but every car is different. i would look at getting it put on a dyno just to see what the AFRs are doing. if they aren't fluctuating in the dead spots then it will be an ignition/electrical issue.

I was having the same issue it seems everyone with the standard ECU and modded R33 GTS-T on here has had.

Get a re-mapped ECU , SAFC or new standalone ECU or change your mods back to stock.

I got a toshi re-mapped ECU and now my engine isn't doing a Paris Hilton anymore.

Hahaha Paris Hilton, that's gold. Sounds like the go...I'll stick her on a dyno and check out the AF ratio. Probably replace the actuator and dump pipe gasket too. And get a Power FC, which I was going to do anyway when my car didn't have issues.

Gotta love cars.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Even more fun, leave all the ADAS stuff plugged in, but in different locations, hopefully avoid any codes!   And honestly, all these new cars with their weird electronics. Pull all the electronics out Duncan, and just shove an aftermarket ECU and if needed a trans controller in, along with a PDM. Make it run basic but race car styled!
    • To follow up a question from earlier too since I had the front bar off again (fking!) This is what is between the bumper and the drivers side wheel And this is the navigator side, only one thing but its a biggy! So basically....no putting coolers in the wheel arches without a lot of moving other stuff. Assuming I move to properly race prepping this car I'll take that job on and see how the computers respond to removing a whole bunch of ADAS modules
    • So I prepped the car for another track day on Wednesday (will be interesting to see coolant temps post flushing out and the larger reservoir, with a forecast of 3-14 being 20o cooler than last time I took it out). Couple of things to mention; since I am just driving the car and not taking a support vehicle, I took the rear seats out and just loaded the back up Team Trackday style. Look at all that space! To cover off removing the rear seat....it is weird (note the hybrid is probably different because it wouldn't have folding rear seats) Basically, you remove the lower seat base, very similar to a r series but it is a clip that pulls forward to release the base rather than it being bolted down. Easy Then, you need to remove the side section of the rear seat on each side. There is a 14mm head nut at the bottom of the side piece, the it slides upwards off a hook at the top to release; you also need to unhook the seatbelt from the loop at the top. Then the centre piece is weird. You need to release/fold the seats forward with the tab in the boot on each side From there, there are 2,x12mm headed bolts holding the rear of each seat to the folding bracket, under the trim between the rear seat and the boot (4x christmas tree clips there, they suck). The seat is out but you can see where the bolts attach to the bracket
    • As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
×
×
  • Create New...