Jump to content
SAU Community

R34 Gtr New Key Coding To Nats System

BookyVL

By BookyVL,
in Car Audio & Electrical

 Share

Recommended Posts

33GTRV Mentor

33GTRV

Posted
Posted

Key cutting is a given-Locksmiths do this for a living. As for the Programming of the NATS key, there are 2 options.

Option 1: Take the key(already cut and ready to go) to your preffered nissan dealership and ask the people there nicely to Program your key to your car, its a 2 min job with a consult system

Option 2: Now this is the tricky bit. It sounds easy and looks easy but its sometimes a pain in the ass if you arent fast enough. There is a simple set of Functions the car can use to recognise you are programming a ke as a secondary option. To do this you will need to:

Here they are....... enjoy!!

ID Code Entry Procedure

To enter the ID code, follow this procedure:

"Setting Mode":

1. Close and lock all doors.

2. Insert and remove the key from the ignition more than six times within 10 seconds. (The hazard warning lamp will flash twice). At this time, the original ID codes are eliminated.

ID Code Entry:

3. Turn ignition key to "ACC" position

4. Push the "lock" button on the new remote control once(for example, if the door is locked using the remote controller during this ID code entry state, a new ID code can be entered). At this time, the new ID code is entered. (The hazard warning lamp will then flash twice).

Additional ID code Entry:

5. If you need to activate additional remote control units, unlock the drivers door, then lock it again(WITH THE DOOR LOCK SWITCH).

6. Push the lock button on the additional remote once.

7. This ID code enable state and setting mode will remain until the drivers door is opened.

NOTE!!

* If you need to activate more than two additional keyless remotes, repeat the procedure "Additional ID code entry" for each new remote.

* If the same ID code that exists in the memory is input, the hazard warning lamps will flash twice but the entry will be ignored.

*Entry of a maximum of four ID codes is allowed and any attempt to enter more will be ignored.

*Any ID codes entered after termination of the "Setting Mode" will not be accepted. Additional keyless remote signals will be inhibited when an ID code has not been entered during the setting mode.

*Some cars that were imported also had a NATS2 system that was varied to the normal Nats. You cant manually program these keys and will need to Take it to a Nissan Dealership to be Programmed with the CONSULT2 system. This may take up to 20 mins and therefore you may be charged a half hour block of labour.

Good Luck and hope this helps!! Might even get a sticky :P

  • 3 weeks later...
aphid Proficient

aphid

Posted
Posted

what if your key doesn't have the remote central locking button? My key is just the standard r34 gtr item

with the logo but no remote central buttons :P

does this mean I need to take it to Nissan to get programmed? Is it possible to program through a laptop via a consult cable??

Thanks ;)

On a side note, Dont go telling the whole world how to do it, there is bound to be some kid in an N13 pulsar that will lock himself out of the Nats ecu lol
FelixTRX Community Regular

FelixTRX

Posted
Posted

Just slightly to the left of this topic, I have a 1999 Nissan Elgrand, it only came with 1 factory key, so we want to get 2 more keys cut. I was told by my alarm installer that I have some kind of key ID ring on my ignition barrel. He said that I have to get factory Nissan keys (not cheap) instead of the normal metal keys that we had with our 1997 Stagea.

Has anybody got around this?

Cheers, Greg.

Chris Rogers Grand Master

Chris Rogers

Posted
Posted

so it has NATS2.8 on it? never seen one with that system there. the keyless side of things yes. never NATS though. is there a blue or red square at the base of the key?

EJD001 Mentor

EJD001

Posted
Posted

Could anyone supply a part number or price for the key in post 10? Im keen on getting a second remote key.. but was told by nissan that it was going to be 330+gst and they couldnt tell me if it was the correct key!

FelixTRX Community Regular

FelixTRX

Posted
Posted

Well Chris, the collar around my ignition barrel is the light, nothing more, nothing less! My mate who installed the alarm must have it confused with something similar to what he sees on newer Nissans!

post-22822-1254712881_thumb.jpg

post-22822-1254712916_thumb.jpg

I have another question regarding stereo wiring but I'll start a new thread for that!

Cheers, Greg.

Chris Rogers Grand Master

Chris Rogers

Posted
Posted
Could anyone supply a part number or price for the key in post 10? Im keen on getting a second remote key.. but was told by nissan that it was going to be 330+gst and they couldnt tell me if it was the correct key!

that is the correct price.. they are NOT cheap.

got a chassis number and I'll look it up for you.

Chris Rogers Grand Master

Chris Rogers

Posted
Posted
Well Chris, the collar around my ignition barrel is the light, nothing more, nothing less! My mate who installed the alarm must have it confused with something similar to what he sees on newer Nissans!

post-22822-1254712881_thumb.jpg

post-22822-1254712916_thumb.jpg

yep thats the plain barrel. the NATS one looks entirely different.

EJD001 Mentor

EJD001

Posted
Posted

I had the same problem whe i got my car.. went to nissan and got a normal steel/ metal key.. got it cut and it does the same job.. except it doesnt have the remote entry to gain access to the vehicle!

ylwgtr2 Grand Master

ylwgtr2

Posted
Posted
what if your key doesn't have the remote central locking button? My key is just the standard r34 gtr item

with the logo but no remote central buttons :thumbsup:

does this mean I need to take it to Nissan to get programmed? Is it possible to program through a laptop via a consult cable??

Thanks :(

I know what your trying to do....you have the key with the red bit yeah?(transponder in there....)Im guessing you want to do that and not the central locking key fob....You maybe able to find a locksmith that has a tool to read your key and program the new key.....I posted the info for the fob quite some time ago here key fob....on another note you can also buy the fob from a nissan dealer and code it even if you dont have one

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Kaptain
      R33 general questions

      By Kaptain · Posted

      Im not entirely sure exactly what or where its leaking from, he started to pull the boots to swap to my new tie rods + ends and it just vomited fluid, so he closed em up up, swapped the rod ends to the old rods and let me know so I can figure a solution out, im guessing its all origional as as I passed 103k miles earlier this year im sure its just in need of a full overhual/rebuild anyways.    If i could just yank it off and be good it wouldn't be an issue to ship it out and wait for the turnaround but the guy I work with doesnt really have space to keep my car for a week or two at a time, would rather drop it off and have a replacement ready to drop in
    • GTSBoy
      R33 general questions

      By GTSBoy · Posted

      What do you mean by "seals"? Internal hydraulic seals (ie, is it leaking PS fluid?) or the rack boots that close the rack onto the tie-rods? Because the former is a rebuild, and the latter is trivial that you or any nearby mechanic could do. Dunno about the cowl. Just buy what you think is required and get anything else you find/break afterwards. Wing? Dunno. Don't like R33s enough to pay attention to them. Mirror glass is just glass (on the surface that you want to polish). Go for it.
    • Kaptain
      R33 general questions

      By Kaptain · Posted

      Hello! Long time lurker, been using the forums to address concerns and questions from afar for a while but I've struggled to find some answers so I guess its about time I made an account and formally asked some more knowledgeable people, since finding local skyline owners is hard (and shops that are knowledgeable or trustworthy to work on 'rare' cars are non existent out where im at, as skylines are quite uncommon to find in the wild around here). So the main 3 questions I have, 1: Steering rack has blown seals, well.. they kind of hold but they are not sealed properly anymore and as my R33 is my DD, i cant exactly rip the rack out and send it off or attempt to fix myself. As most refurb ones are around $1,100 or more shipped, and I have other things I need to work on around the car, I was seeking clarification on whether an S15 rack will more or less bolt right in, and whether a common mechanic could do any other required work to get it to fit. I ask, as I've found a supplier than can sell a manufactured as oem one for around 400, if not I'll likely order a used one from Jacks JDM, and take a risk on the seals there. The second question i have is that im replacing the front wiper cowl and have planned to buy 4 new clips and a new center clip but wasnt sure if there were any other clips that would also need to get replaced while I was at it. Given im sure any that are there now will simply break when I remove the old cowl... Last thing would be a fairly straight forward question, i think. If I manage (strong if, finding one has proven to be a pain) to find a R33 GTR spoiler/wing will it require much modification to bolt to a S2 R33 GTST? I've read the bolt patterns dont match but otherwise would bolt in, only options I have found with much luck is China stuff on ebay and carbonetics, which has a nice $650 shipping fee... so if anyone has any pointers where a US chap could locate one that would be great Random side question as well, the mirrors as I understand are mirror glass, and as im planning to polish my windows from water spots and surface scratches, i was hopeful cerium oxide would be fine for them too, as my research points to, but clarification is always nice. Any pointers would be appreciated, and while I have scoured the internet for answers if I missed a prior post somewhere that may answer these directly please point me towards it, as i must have simply missed it. I have seen a post here or there that has mentioned it, but I usually get 50-50 answers, or half answers... I dont have a lot of fab experience or mechanic experience, outside of hydraulic and pneumatic stuff I did in the military and with how hard it is to source stuff in the US, id rather not wing it and hemmoraghe money lol. Thanks guys! Sorry for the monumental first post haha
    • AdiR34
      Did tie rods. Steering now not "springing" back.

      By AdiR34 · Posted

      Yep, there's a very minor drift left that happens a few seconds after letting go of the steering wheel, but not enough to bother me. Enjoying the car still!
    • Keeper
      S A U N S W Club Membership

      By Keeper · Posted

      Got you mate. Check your email!
×
×
  • Create New...