Jump to content
SAU Community

Recommended Posts

Hey Team,

I have been waiting for a while for my size semi slicks, but nothing yet, I now have 10-20% tread left and I need tyres before my next sprint round.

So my question is, I know I'll be losing 20mm of track - but overall, how would it effect my handling? is it going to be different in anyway, shape or form??

do I just wait and hope my supplier can get the 205's before mid October (50% chance!!) or take the gamble and get the 195's ?

(this is for my mx5, not a skyline too :O )

Cheers,

Chris

Link to comment
https://www.sau.com.au/forums/topic/288695-tyre-width-noticable-difference/
Share on other sites

You won't lose any "track" - that is controlled by the wheel design, specifically the offset.

So I doubt you'll notice much difference at all in handling with 10mm less rubber width.

yeah unlikely you will notice the difference. and for sure a good tyre 10mm narrower will still handle better than a wider, worserer tyre.

in fact for supersprints you may find it improves times as they will come up to temp a little quicker, and may not go off with a short run

Give hornibrook tyres a call and see if they can get your size.

I recently picked up some new re55's for 380 a corner inc shipping, which isn't far off the 340 i paid for r888's at taleb last time.

I'm not sure if the pricing was specific to the size i bought but it's worth a shot regardless.

if you were to be using the same compound tyre etc, but 10mm skinnier then there is going to be a difference on performance. and it won't always be bad, but there will be some negatives. overall you are losing 40mm of tyre (assuming you need the tyres for both front and rear). which is nearly 5%

negatives of skinnier tyres:

less traction off the line

less grip when cornering and braking

go off quicker

positives of skinnier tyres:

less rolling resistance (faster acceleration once traction is no longer an issue and higher top speed)

lighter (again, faster acceleration) (yes i know that the weight difference will be minimal but every little bit helps in a race)

come up to temp quicker (so more grip earlier)

Hi everyone.

Was about to post a similar question but hope it's ok if I ask it here. :thumbsup:

Im looking at a set of 18" rims, 8.5 front, 9.5 rear, that come with tyres 245/40 front, 275/40 rear.

I understand that to fit in my guards I have to look at getting smaller tyres, 225/40 front, 245/40 rear. The tyres I'm looking at don't come in 245/40, only up to 235/40.

Would it be ok to get the 235/40 for the rear? I have an r32 gts-t 4door. I don't do any aggressive driving, mostly daily driving to work and highway kms as well.

Thanks for any help.

Kye

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • perhaps i should have mentioned, I plugged the unit in before i handed over to the electronics repair shop to see what damaged had been caused and the unit worked (ac controls, rear demister etc) bar the lights behind the lcd. i would assume that the diode was only to control lighting and didnt harm anything else i got the unit back from the electronics repair shop and all is well (to a point). The lights are back on and ac controls are working. im still paranoid as i beleive the repairer just put in any zener diode he could find and admitted asking chatgpt if its compatible   i do however have another issue... sometimes when i turn the ignition on, the climate control unit now goes through a diagnostics procedure which normally occurs when you disconnect and reconnect but this may be due to the below   to top everything off, and feel free to shoot me as im just about to do it myself anyway, while i was checking the newly repaired board by plugging in the climate control unit bare without the housing, i believe i may have shorted it on the headunit surround. Climate control unit still works but now the keyless entry doesnt work along with the dome light not turning on when you open the door. to add to this tricky situation, when you start the car and remove the key ( i have a turbo timer so car remains on) the keyless entry works. the dome light also works when you switch to the on position. fuses were checked and all ok ive deduced that the short somehow has messed with the smart entry control module as that is what controls the keyless entry and dome light on door opening   you guys wouldnt happen to have any experience with that topic lmao... im only laughing as its all i can do right now my self diagnosed adhd always gets me in a situation as i have no patience and want to get everything done in shortest amount of time as possible often ignoring crucial steps such as disconnecting battery when stuffing around with electronics or even placing a simple rag over the metallic headunit surround when placing a live pcb board on top of it   FML
    • Bit of a pity we don't have good images of the back/front of the PCB ~ that said, I found a YT vid of a teardown to replace dicky clock switches, and got enough of a glimpse to realize this PCB is the front-end to a connected to what I'll call PCBA, and as such this is all digital on this PCB..ergo, battery voltage probably doesn't make an appearance here ; that is, I'd expect them to do something on PCBA wrt power conditioning for the adjustment/display/switch PCB.... ....given what's transpired..ie; some permutation of 12vdc on a 5vdc with or without correct polarity...would explain why the zener said "no" and exploded. The transistor Q5 (M33) is likely to be a digital switching transistor...that is, package has builtin bias resistors to ensure it saturates as soon as base threshold voltage is reached (minimal rise/fall time)....and wrt the question 'what else could've fried?' ....well, I know there's an MCU on this board (display, I/O at a guess), and you hope they isolated it from this scenario...I got my crayons out, it looks a bit like this...   ...not a lot to see, or rather, everything you'd like to see disappears down a via to the other side...base drive for the transistor comes from somewhere else, what this transistor is switching is somewhere else...but the zener circuit is exclusive to all this ~ it's providing a set voltage (current limited by the 1K3 resistor R19)...and disappears somewhere else down the via I marked V out ; if the errant voltage 'jumped' the diode in the millisecond before it exploded, whatever that V out via feeds may have seen a spike... ....I'll just imagine that Q5 was switched off at the time, thus no damage should've been done....but whatever that zener feeds has to be checked... HTH
    • I think Fitmit had some, have a look on there (theyre Australian as well)
    • Hah, fair enough! But if you learn with this one you can drive any other OEM manual. No modern luxury features like auto rev-matching or hillstart assist to give you a false sense of confidence. And a heavy car with not that much torque so it stalls easily. 
×
×
  • Create New...