Jump to content
SAU Community

Recommended Posts

Hey Team,

I have been waiting for a while for my size semi slicks, but nothing yet, I now have 10-20% tread left and I need tyres before my next sprint round.

So my question is, I know I'll be losing 20mm of track - but overall, how would it effect my handling? is it going to be different in anyway, shape or form??

do I just wait and hope my supplier can get the 205's before mid October (50% chance!!) or take the gamble and get the 195's ?

(this is for my mx5, not a skyline too :O )

Cheers,

Chris

Link to comment
https://www.sau.com.au/forums/topic/288695-tyre-width-noticable-difference/
Share on other sites

You won't lose any "track" - that is controlled by the wheel design, specifically the offset.

So I doubt you'll notice much difference at all in handling with 10mm less rubber width.

yeah unlikely you will notice the difference. and for sure a good tyre 10mm narrower will still handle better than a wider, worserer tyre.

in fact for supersprints you may find it improves times as they will come up to temp a little quicker, and may not go off with a short run

Give hornibrook tyres a call and see if they can get your size.

I recently picked up some new re55's for 380 a corner inc shipping, which isn't far off the 340 i paid for r888's at taleb last time.

I'm not sure if the pricing was specific to the size i bought but it's worth a shot regardless.

if you were to be using the same compound tyre etc, but 10mm skinnier then there is going to be a difference on performance. and it won't always be bad, but there will be some negatives. overall you are losing 40mm of tyre (assuming you need the tyres for both front and rear). which is nearly 5%

negatives of skinnier tyres:

less traction off the line

less grip when cornering and braking

go off quicker

positives of skinnier tyres:

less rolling resistance (faster acceleration once traction is no longer an issue and higher top speed)

lighter (again, faster acceleration) (yes i know that the weight difference will be minimal but every little bit helps in a race)

come up to temp quicker (so more grip earlier)

Hi everyone.

Was about to post a similar question but hope it's ok if I ask it here. :thumbsup:

Im looking at a set of 18" rims, 8.5 front, 9.5 rear, that come with tyres 245/40 front, 275/40 rear.

I understand that to fit in my guards I have to look at getting smaller tyres, 225/40 front, 245/40 rear. The tyres I'm looking at don't come in 245/40, only up to 235/40.

Would it be ok to get the 235/40 for the rear? I have an r32 gts-t 4door. I don't do any aggressive driving, mostly daily driving to work and highway kms as well.

Thanks for any help.

Kye

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Well, my new WMI system took much longer to finalize. I actually missed my dyno appointment last Friday and lost my 150$ deposit. I'll be going back in the next week or two.  To sum it up. I only kept the AEM tank from my old setup. I replaced the AEM pump with a higher flow/pressure ProMeth 30GPH pump. I also swapped over to a 6AN low pressure feed line to the pump from the tank. There's also a pressure switch you cannot see on the pump high pressure line.    This is feeding 6x 200CC direct port nozzles and 1x 500CC Pre Throttle body nozzle. All fittings are Swagelok, because well why not. I also have a 300PSI pressure sensor up front.    I now have my Haltech ECU controlling everything. I start my pump with a basic relay at 5PSI and deadhead it. I then PWM a 3000CC methanol Injector to control flow starting around 10psi. The pressure switch in the trunk, along with my tank level are safeties before I ever get to 10PSI, and then I use my pressure sensor upfront as a secondary safety to cut the WMI and corrections in case the injector blocks or a line ruptures.  Wish me luck on the dyno!    
    • So, I'm back with bad news. There's no jack long enough on this planet that will reach the front subframe. If by some chance there is, it would weigh 200lb's.  I purchased a long reach jack... The damn thing weighted 120lb's and was massive. Didn't even come close, was still short at least a foot. It was a pain, but I brought it back. Next I decided HA! No problem, I'll get an Extra long reach jack. Well, I couldn't lift the box... It must have weighed 160LB's and luckily there was an open box in store. I took measurement and was still nowhere close.  Sadly I've lost hope and have accepted defeat. 
    • Thanks for that tip, niZmO_Man. I think the battery is OK. It's quite a new one, but I'll check. Last time I needed a new battery, everything electronic was fine, except that there wasn't enough current to turn over the starter. I decided to order one of the partial AV system translation CDs from Car Audio Workshop in NZ. That might have some effect, or help me diagnose the date problem. 🤞
    • I suppose it was relatively stock too, the JZ motor handle most mods thrown at them without even breaking a sweat 
    • I saw your intro update, are you sure you've actually had a starter motor failure? You mention it could be the alarm causing it. I'm assuming you've got a no start issue, but what are the exact symptoms, as there could be a few reasons it has stopped wanting to start.
×
×
  • Create New...