Jump to content
SAU Community

Recommended Posts

just bought a nitrous system for 700 buks, second hand but never been used. come with a 25lb bottle and bottle warmer!!

Planning on hooking it to my rb20 "32 A.S.A.P

Just wondering on the power increase figures?? It come with a 150hp "jet" and a 200hp "jet"

I no what the jet does and so on but im wondering it this will give me an instant extra 150-200hp?

And mostly will the motor be able to handle this NOS!

Link to comment
https://www.sau.com.au/forums/topic/288873-nitrous/
Share on other sites

What is currently done to the car? We talking a wet kit or a dry kit? What brand? Lol i wouldnt be putting such high jets into the car if it is fairly standard, that is a lot of nitrous and fuel and if you don't know what you are doing you will kill it instantly. Use a 75HP shot and see how you go, work your way up. Make sure your injectors and pump are good. Do you know much about nitrous? By the sounds of things i don't think you do. Take it to some one that knows what they are doing, if not you will do some damage...

Power figures vary from engine to engine, but in essence yes, it will give those approximate numbers if the fuel jet and nitrous jet are the right sizes.

Edited by PM-R33
Link to comment
https://www.sau.com.au/forums/topic/288873-nitrous/#findComment-4838070
Share on other sites

there is a place in ballarat that refills the bottle

getting DR DRIFT to do the install and potential tune and its only guna be used for racing purpose only.

And na i dont need nos to get past the 180, because its hits 180 in 3rd with an auto....

Link to comment
https://www.sau.com.au/forums/topic/288873-nitrous/#findComment-4839383
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • Got the passenger door on plus the master cylinder and booster. Loaded up to take it home. At home, the colour changes a lot in the light.
    • Nothing cheap, but I have seen the AC Hydraulic DK13HLQ which is pretty close to what you're asking for. The problem is the hydraulic cylinder mandates that the back of the jack be a certain height and Skylines have fairly deep inset floor jack points. A more certain and cheap option is to get some nominal 2x10 inch lumber boards and have one board be 1.5 feet, the other board 3 feet. Glue it all together with lots of clamps to maintain pressure. Make two of these. The ramp suggested above is a good idea, it takes quite a bit of clutch slip to get over each of the boards. I only need the first ~1.5 inches for my low profile jack on a standard ride height car but a lowered car you want to go up to the full ~3-3.5 inches. Paint it or store indoors if you want it to last.
    • Ok. And Nistune? I read (here too) mainly on Stagea threads that it can by "turn off" with Nistune. But they say they still had the sensor plug in. Next week iam going to the Nistune(and other ECUs) tuner so i can finally make it work. I drove the car home and apart from the cut it drove great. No misfire no smoke no hesitation or rough start...so hoping it is this sensor that is missing  
    • I just stack 2 pieces of 200x50 timber on top of each other. Total length about 900mm, with the top one being a little shorter and both having a 45° angle cut on them to make the front edge a bit of a ramp. Put these in front of each front wheel, drive up on them, throw the trolley jack under. Takes 1 minute. Scissor jacks can eat a bowl of dicks. I never use on under my car unless desperate.
    • Well, yeah. But I just expect everything other than my car to feel like a bucket of shit anyway. I still miss my Alfa 116 so much though. You could run over a 20c piece and tell whether it was heads or tails.
×
×
  • Create New...