Jump to content
SAU Community

Is It Just Me....

Duncan

By Duncan,
in New South Wales

 Share

Recommended Posts

  • Replies 49
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

Posted Images

Wacky Dee Veteran

Wacky Dee

Posted
Posted

my window was open this morning as I was still sleeping and I kept waking up as I had difficulties breathing ... then when I finally did get up I realized what's up. f**king hell, I might have some early stages of asthma I think I'm starting to panic.. so hard to breathe even with all windows closed

Even the car started behaving weirdly .. just went to the local shops to buy some milk and sitting at the lights the revs got stuck at 2000rpm until I blipped the throttle a bit ..thena while later SLIP light came on. It's gotta be the dust messing the sensors or intake up

Xmetal Mentor

Xmetal

Posted
Posted

Apparently the wind is supposed to ease off in the afternoon. I'll be out watching for a good sunset. :D

Those of you with SLR and DSLR cameras be advised that it is NOT a good idea to change lenses OUTSIDE your car or house.

~ Jay ~ Enthusiast

~ Jay ~

Posted
Posted
Apparently the wind is supposed to ease off in the afternoon. I'll be out watching for a good sunset. :D

Those of you with SLR and DSLR cameras be advised that it is NOT a good idea to change lenses OUTSIDE your car or house.

Yea thats a good point im doing the same thing with our AV gear the warehouse is all closed up and all my gear onsite im keeping covered if possible its bad enough doing jobs near a beach then you open up the mixers a few weeks later to see why its not working and you find its all rusted from the salty air.

astrotristan Grand Master

astrotristan

Posted
Posted

lolz one of my friends in the city (brisbane) just called me, her building was evacuated and ppl were chilling on the streets, n there are/were ambos and firefighters around trying to calm ppl down

wouldnt being inside be safer? hmm idk lol

Brandon Veteran

Brandon

Posted
Posted
I slept with my window open last night and woke up with my whole room, closet and ensuite covered in dust! It's gonna take ages to clean! :P

Hahaha. Thats gonna be a disaster!

The sky is getting red-er here in Brisbane too as we speak

NZM.031 Grand Master

NZM.031

Posted
Posted
Yeah skies starting to go orange up here :S

I can hear a remix of a Deep Purple song coming along... Dusttt on the waterr... FIRE IN THE SKY!!

Sorry couldn't resist :P

shouldnt that be "duuusst on the skyline... and now dust in your eye."

~ Jay ~ Enthusiast

~ Jay ~

Posted
Posted
took this photo this morning. thought i would stay home after seeing this.

:P

Hahahah Awesome picture do u live just above LUNA PARK the company i work for just took over as the Inhouse Audio Visual Company which is kinda cool we get heaps of work there now

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • TurboTapin
      R32 GTST - 600KW+ RB28/CD009 Build

      By TurboTapin · Posted

      Well, my new WMI system took much longer to finalize. I actually missed my dyno appointment last Friday and lost my 150$ deposit. I'll be going back in the next week or two.  To sum it up. I only kept the AEM tank from my old setup. I replaced the AEM pump with a higher flow/pressure ProMeth 30GPH pump. I also swapped over to a 6AN low pressure feed line to the pump from the tank. There's also a pressure switch you cannot see on the pump high pressure line.    This is feeding 6x 200CC direct port nozzles and 1x 500CC Pre Throttle body nozzle. All fittings are Swagelok, because well why not. I also have a 300PSI pressure sensor up front.    I now have my Haltech ECU controlling everything. I start my pump with a basic relay at 5PSI and deadhead it. I then PWM a 3000CC methanol Injector to control flow starting around 10psi. The pressure switch in the trunk, along with my tank level are safeties before I ever get to 10PSI, and then I use my pressure sensor upfront as a secondary safety to cut the WMI and corrections in case the injector blocks or a line ruptures.  Wish me luck on the dyno!    
    • TurboTapin
      Jacks that fit under GTR lips that can reach the subframe?

      By TurboTapin · Posted

      So, I'm back with bad news. There's no jack long enough on this planet that will reach the front subframe. If by some chance there is, it would weigh 200lb's.  I purchased a long reach jack... The damn thing weighted 120lb's and was massive. Didn't even come close, was still short at least a foot. It was a pain, but I brought it back. Next I decided HA! No problem, I'll get an Extra long reach jack. Well, I couldn't lift the box... It must have weighed 160LB's and luckily there was an open box in store. I took measurement and was still nowhere close.  Sadly I've lost hope and have accepted defeat. 
    • suko
      J50 clock date suddenly reset to January 1

      By suko · Posted

      Thanks for that tip, niZmO_Man. I think the battery is OK. It's quite a new one, but I'll check. Last time I needed a new battery, everything electronic was fine, except that there wasn't enough current to turn over the starter. I decided to order one of the partial AV system translation CDs from Car Audio Workshop in NZ. That might have some effect, or help me diagnose the date problem. 🤞
    • Dose Pipe Sutututu
      Chris' Toyota Mark ii JZX110

      By Dose Pipe Sutututu · Posted

      I suppose it was relatively stock too, the JZ motor handle most mods thrown at them without even breaking a sweat 
    • MBS206
      Starter motor replacment teeth count.

      By MBS206 · Posted

      I saw your intro update, are you sure you've actually had a starter motor failure? You mention it could be the alarm causing it. I'm assuming you've got a no start issue, but what are the exact symptoms, as there could be a few reasons it has stopped wanting to start.
×
×
  • Create New...