Jump to content
SAU Community

Bosch 040 Just Got More Noisy!?!

Yeedogga

By Yeedogga,
in Engines & Forced Induction

 Share

Recommended Posts

Yeedogga Experienced

Yeedogga

Posted
Posted (edited)

Hi guys,

I put an 040 in the car a few months ago. Ran fresh wiring, new relay etc etc

Up until today, you could just hear it humming/sucking away. From inside the car you could just hear over the exhaust & from the outside you could barely hear the pump at all.

Today it has started whining/buzzing and it is significantly louder than normal. Should I be worried?

Edited by Yeedogga
Link to comment
https://www.sau.com.au/forums/topic/289920-bosch-040-just-got-more-noisy/
Share on other sites
turael Enthusiast

turael

Posted
Posted

if it makes you feel better, my 040 makes a hell of a lot of noise, all the time. gurgles, buzzes, whining...

very noisy pump. car has always been fine though, been running it for a year or two now.

Parag0n Mentor

Parag0n

Posted
Posted
I don't have a gauge so I haven't been able to tell. Car seems to be running fine though.

Mate go get an autometer gauge that you can put in your engine bay they're like $20 and hook it up to your regulator, its such a cheap mod for important information if you're running more than base fuel pressure.

femno Grand Master

femno

Posted
Posted

Check your tank for shit!

Pull the pump out and inspect it for black dusty crap on the bottom. If that or anything else is on the strainer of the pump you need to remove the tank and have it cleaned.

James_03 Mentor

James_03

Posted
Posted

My 044 went this way too, exact same symtoms. Started also getting fluctuating pressure.

Ripped it out and went a 023, still never figured out why it died. Was a genuine 044 too, strainer was clean, good wiring etc.

There just getting so hit/miss now it's not funny.

bubba Grand Master

bubba

Posted
Posted (edited)

I really don't think it's anything to worry about, my 044 has been like this for a couple of years now with no issues what-so-ever.

My guess as to WHY is that it's probably working harder to pump the thinner hotter fuel around. It's basically because there is excess fuel travelling to a hot engine bay and back. Standard, our cars run a control module that drops voltage to the fuel pump at idle, these tend to get removed when aftermarket fuel pumps go in.

Edited by bubba
Mayuri Krab Grand Master

Mayuri Krab

Posted
Posted
if it makes you feel better, my 040 makes a hell of a lot of noise, all the time. gurgles, buzzes, whining...

very noisy pump. car has always been fine though, been running it for a year or two now.

Same with mine. Mine has a very loud buzz & grgule sound since day 1 of getting it installed when my stock one died. The exhaust noise covers the pump noise up inside the car, however outside its very noticeable when you are near the rear of the car.

Being fine for about close to a year now.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • RP1421
      S15 Spec R

      By RP1421 · Posted

      As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • joshuaho96
      R32 GTS (RB20DE) Injectors Replacement

      By joshuaho96 · Posted

      I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
    • perry_r33
      R34 GTR Vspec Garage Sale - All must go!

      By perry_r33 · Posted

      Pm sent 
    • Robot
      Skyline v36 350GT sedan hunting on idle

      By Robot · Posted

      Hi,  Just joined the forum so I could share my "fix" of this problem. Might be of use to someone. Had the same hunting at idle issue on my V36 with VQ35HR engine after swapping the engine because the original one got overheated.  While changing the engine I made the mistake of cleaning the throttle bodies and tried all the tricks i could find to do a throttle relearn with no luck. Gave in and took it to a shop and they couldn't sort it. Then took it to my local Nissan dealership and they couldn't get it to idle properly. They said I'd need to replace the throttle bodies and the ecu probably costing more than the car is worth. So I had the idea of replacing the carbon I cleaned out with a thin layer of super glue and it's back to normal idle now. Bit rough but saved the car from the wreckers 🤣
    • GabsReDeal
      R32 GTS (RB20DE) Injectors Replacement

      By GabsReDeal · Posted

      After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
×
×
  • Create New...