Jump to content
SAU Community

Recommended Posts

Ok guys ...

clearing out some space to make way for new useless junk :(

There may be more shiet that i find that isnt listed, but whatever is here, ill throw your way free of charge ;)

For just 1.5k flat you will get the following and then some:

[referring to OEM factory stock r34 vspec 2 parts - all in perfect working order no issues guaranteed]

- shocks and springs

- cam cover

- cam gears

- pulleys

- camshafts

- injectors

- front and rear camber arms

- fuel pump

- gtr engine plaque

- fmic + bovs + all piping / hosing

- radiator

- tail lights

- turbos

Random

- brand new trust air filter.

- twin trust filters

- nismo gear knob

Thats all i can think of for now. As i said, if theres anything else i find, ill throw it your way.

Any questions, dont hesitate to PM me

Most PMs have been replied to ... have some kind of 5 minute limit to reply between each pm ...

Would prefer to sell everything but see how things goes ..

Also just found

- nismo oil cap

- vspec 2 ecu

- oem single din pocket

- the turbos have the stock dump pipes attached

- hks ssqv brand new purple fin

- project mu brake pads front and rear with about 80-90% pad left

- random hoses + pipes

pics will be up tonight

All that plus the original post for just 1.5k!!!

Edited by Phantom Snail
are the tail lights complete? (including outer plastic housings)

no they dont have the outter plastic, thats still on the car.

Basically i removed these to fit nismo ones .. so its the light and the wires .. not the housing on the car

mate im keen on the nismo oil cap, are willing to seperate?? is it genuine, pics?

I may separate depending on the interest i get on all parts .. it seems positive and likely at this stage that i may separate ... will wait for further replies to confirm

Yes it is genuine, pictures of most of the stuff will be up tonight

how much for the ssqv??? and where are you at?

Its just the purple fin, not the actual bov.

Im located in Sydney, Fairfield East. Pick up is not a problem.

Ok guys ... as promised, the pictures of most of the items

Please disregard the boxes/packaging that you may see the items in, they are the items i had upgraded to, and the standard oem parts were placed back in the corresponding packages

IMG_1274.jpg

IMG_1275.jpg

IMG_1276.jpg

IMG_1277.jpg

IMG_1278.jpg

IMG_1279.jpg

IMG_1280.jpg

IMG_1281.jpg

IMG_1282.jpg

IMG_1283.jpg

IMG_1284.jpg

IMG_1285.jpg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • My guesstimate, with no real numbers to back it up, is it won't effect it greatly at all.its not a huge change in position, and I can't see the air flow changing from in turbulence that much based on distance, and what's in front of it. Johnny and Brad may have some more numbers to share from experience though.
    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
    • Pull codes via the self-diagnosis procedure. As far as I can tell this is just a sign of transmission issues but not a code unto itself.
×
×
  • Create New...