Jump to content
SAU Community

Recommended Posts

i found a turbo package kit that comes with a brand new t04e turbo, a manifold and a wastegate for about $700 on ebay for a rb20det. Now, im not that kind of guy that will just buy something as soon as he sees it. Is the t04e turbos for rb20det's any good? Can i expect a large increase in horsepower?what are your personal opinions?

Im kind of stuck between either buying this or buy a rb25det s2 turbo.

any help/information would be great. Thanks

Link to comment
https://www.sau.com.au/forums/topic/290422-t04e-turbo-for-rb20det/
Share on other sites

So you will need an ECU(Nistune or standalone) and injectors, fuel pump. GTR injectors can handle 260+. I do not know if this turbo will do it, but there is a very large gap between 250 and 300. That is the difference between a GCG Highflow and a GT3076.

Personally I would be aiming for the lower more responsive figure if it is a street car.

Is this a planned purchase or an impulse buy due to seeing it for sale?

impluse buy. Im not trying to make it a track car. Its just that someone told me they would sell me a s2 rb25 turbo for $430 and i seen this kit on ebay for $700 and thought... "hmm....pay extra $200 and get a aftermarket turbo with much more power".

Im not trying to get it to 250kw straight away, but this turbo can be one of the first steps. Later on ill get internals done, cam gears etc...

so, if i do get this t04e, ill need a fuel pump, which will set me back $200, nistune chip which will be about $500 and some injectors which i dont know how much they cost(how much are gtr injectors?)

you reckon i should get it or a rb25turbo?

Ebay - i knew before i even opened the thread it would be a typical 'ebay special'...

A t04e, if its the typical style, will not be useful on the RB20. You will not even see reasonable boost before 4500-5000rpm. You'll make 250rwkw (maybe) but it will be the shittiest car to drive you will hate it. I had a t04e on my RB25 (car came like that), and it was appaling.

$700 is cheap for a turbo kit - so think about it, why is it THAT cheap? A DECENT kit costs over $3500

If you want a decent and reasonable upgrade for the RB20 - put a RB25 turbo on there like everyone else does. Best bang for your dollar.

BTW - I've edited your signature, please keep them clean. This is site that does not really condone vulgar displays.

$3500 for a single turbo kit is kinda going off the deep end... if it is a Garrett T04E then you will have horn old school turbo lag like an 80's performance car.

Don't know about ebay turbos apart from that they are shit and you'd be best off leaving them for VL owners.

have one on my car dude...its making 250rwkw at 14.5psi.....problems are that it is laggy as shit....max torque is at 4600rm... is it externally gated??.. are you gonna high mount it?? u have a lot of things to do b4 chuckin it on.... man..save your money for a little longer and chuck on something respectable like a gt3076r... great power..great response..ggreat reliablity....poor man pays twice... trust me.... i god dam hate my t04e

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...