Jump to content
SAU Community

Recommended Posts

  • Replies 14.2k
  • Created
  • Last Reply

Top Posters In This Topic

nice, I'm hopeing to rip some lips in whyalla and maybe nab some swimmers from sunday

theres mulloway from the ardrossan jetty at nite, tommies and gar at rapid bay and blueys at ardrossan and moonta jetty

the good stuff still needs a boat tho...

im going to ardrossan tomorrow arvo for some crabs and squiddies... should at least get fed

-D

youd like that matty, wouldnt you? damn 31 pilots.

lol, nah, ur not my type. bit more girly like heslo and you might be in :blink:

Matty, make it 12 tomoz?

we got a second inspection on the property we lookin at, at 10.30

no worries, gotta make sure im back down for my appointment at the bank at 3:30. shouldnt take long to get it on and get up there. she moves alright now i take it?

im 3/4 cut on coopers

and im cranking chuck berry

'no particular place to go'

i double dare you soft bitches to play anything as hard as chuck within the next 60 minutes

otherwise i'll pee on ur mojo

-D

theres mulloway from the ardrossan jetty at nite, tommies and gar at rapid bay and blueys at ardrossan and moonta jetty

the good stuff still needs a boat tho...

im going to ardrossan tomorrow arvo for some crabs and squiddies... should at least get fed

-D

Fark! I thought you were going Sunday :blink:

Then again I might be scamming a spot on a charter out of Balgowan if all goes well

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • The wiring diagram for the R33 RB25 is freely available, and is essentially the same same as most other RBs (just with differences as to which pin # does which job). To get the ECU to power up, you just need to provide power to the ECCS relay, and have the other power feeds that come in from the top left of the wiring diagram (wrt the ECU) that give perma power to the fuel pump relay, the ECU itself, etc etc, all connected. When you put power on all these it will just come to life. It's pretty clear from the diagram what needs to happen. Just follow the lines from the 12V + supply stuff in the top left over towards the ECU. I've even posted snips of such diagrams (not for vanilla 25, I think for Neo and 26) to various threads here in the last few months, talking about what it takes to get the fuel pump and FPCM up and going. Search these up and they will help get you started on doing the same with the vanilla 25 diagram. Hell, for all I know, I've done the same with that one in years past and have forgotten.
    • Yep...so unless someone posts up the answer you will need to probe from the ECU connector to the dash plug with a multi meter in continuity mode to trace the wires.  Note the ECU has multiple - and + (and across different key settings - Battery, IGN and Start) and most likely the power is fed from the connector(s) that is normally near the left hand headlight.
    • Thanks Duncan, I am actually just trying to get the Rb turning and running with the RB25DET S2 original loom itself  I am just trying to get it going outside the body and not thinking about the S15 or trying to match anything to the S15 loom at all I am only trying to see if anyone has done this and what pin they found to be the ignition trigger and ECU+/- on the dash connector, that's about it. Thanks  
    • Hi Guys, Does anyone know any aftermarket part numbers for a starter motor to suit the VQ25DET? I can find lots of alternative part number for the VQ35DE, which I assume would fit, but there is a lot of conflicting information out there. Thanks..
    • I don't understand how this hasn't boiled down to - Upgrade the turbo when you have everything required. ECU, injectors, fuel pump, turbo, etc. Do it all at once.  If you don't have everything required, just enjoy the car as it is and keep saving up your pennies. 
×
×
  • Create New...