Jump to content
SAU Community

Recommended Posts

  • Replies 14.2k
  • Created
  • Last Reply

Top Posters In This Topic

ive checked all 16 pages of the diy thread..... how do i remove all the hicas pumps in engine bay correctly and how do i remove the abs?? anyone now of a step by step information page?

Jenkies u will need a non abs brake master cylinder and possibly some new lines made.

And Jake I'm not a mechanic I just know some car info lol

aww man thanks... nothing is ever perfectly easy is it :)

see my gtr for an example :) i dont regret not having abs, it hardly ever locks and when it does its pretty easy to ease off and get it gripping.

mine is the opposite.. i find it pritty easy to lock all 4s up with ABS, but that might have something to do with tyres XD

you bloody legend! ive never ever had the abs actually work on me which means my pedal control must be decent.. need the space to mount a catch can so i can leave battery in bonnet! thanks again chad

Anyone know how to replace wheel bearings? or a link to how to do it...

you'll need a press as they are pressed into the hubs, And if they are anything like the S-Series they are like $90 each for the bearings.

Jenkies u will need a non abs brake master cylinder and possibly some new lines made.

And Jake I'm not a mechanic I just know some car info lol

He can just split the front and rear lines and then put a biasing valve on the rear line. regency will be happier with a factory non abs setup though. although he'll have bigger problems if regency ever look at the car.

Edited by D_Stirls
mine is the opposite.. i find it pritty easy to lock all 4s up with ABS, but that might have something to do with tyres XD

what tyres you got? i got cheapish tyres (nankangs) but mine are 275s all round so that probably helps me a fair bit.

and also post-31501-1263854503_thumb.jpg 4466

Edited by Inline 6
Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • For once a good news  It needed to be adjusted by that one nut and it is ok  At least something was easy But thank you very much for help. But a small issue is now(gearbox) that when the car is stationary you can hear "clinking" from gearbox so some of the bearing is 100% not that happy... It goes away once you push clutch so it is 100% gearbox. Just if you know...what that bearing could be? It sounding like "spun bearing" but it is louder.
    • Yeah, that's fine**. But the numbers you came up with are just wrong. Try it for yourself. Put in any voltage from the possible range and see what result you get. You get nonsense. ** When I say "fine", I mean, it's still shit. The very simple linear formula (slope & intercept) is shit for a sensor with a non-linear response. This is the curve, from your data above. Look at the CURVE! It's only really linear between about 30 and 90 °C. And if you used only that range to define a curve, it would be great. But you would go more and more wrong as you went to higher temps. And that is why the slope & intercept found when you use 50 and 150 as the end points is so bad halfway between those points. The real curve is a long way below the linear curve which just zips straight between the end points, like this one. You could probably use the same slope and a lower intercept, to move that straight line down, and spread the error out. But you would 5-10°C off in a lot of places. You'd need to say what temperature range you really wanted to be most right - say, 100 to 130, and plop the line closest to teh real curve in that region, which would make it quite wrong down at the lower temperatures. Let me just say that HPTuners are not being realistic in only allowing for a simple linear curve. 
    • I feel I should re-iterate. The above picture is the only option available in the software and the blurb from HP Tuners I quoted earlier is the only way to add data to it and that's the description they offer as to how to figure it out. The only fields available is the blank box after (Input/ ) and the box right before = Output. Those are the only numbers that can be entered.
    • No, your formula is arse backwards. Mine is totally different to yours, and is the one I said was bang on at 50 and 150. I'll put your data into Excel (actually it already is, chart it and fit a linear fit to it, aiming to make it evenly wrong across the whole span. But not now. Other things to do first.
    • God damnit. The only option I actually have in the software is the one that is screenshotted. I am glad that I at least got it right... for those two points. Would it actually change anything if I chose/used 80C and 120C as the two points instead? My brain wants to imagine the formula put into HPtuners would be the same equation, otherwise none of this makes sense to me, unless: 1) The formula you put into VCM Scanner/HPTuners is always linear 2) The two points/input pairs are only arbitrary to choose (as the documentation implies) IF the actual scaling of the sensor is linear. then 3) If the scaling is not linear, the two points you choose matter a great deal, because the formula will draw a line between those two points only.
×
×
  • Create New...