Jump to content
SAU Community

Recommended Posts

  • Replies 14.2k
  • Created
  • Last Reply

Top Posters In This Topic

Abe i would also not get organic with a skylines get a

Ceramic Cushioned then you have the strength of the ceramic and drive ability of cushioned

But doesn't an organic allow you to slip it a bit more!?

So no matter what i really choose, someone is going to say "I wouldn't have chosen that clutch kit" or "Why did you get that one" or some other comment. Why cant choosing a clutch be easier :) , too many contradicting comments/opinions.

Attention: Nightcrawler and Aberax.

Taken from my facebook minutes ago.

4amw.jpg

:O:(:(

:) .....oh, i get it now :blink: ...and it wasn't 4am either, was more like 1-2am...4am was pretty much when we had to get up. Remind me never to share a room/house with you and David again ;)

<snip>

:) .....oh, i get it now :blink: ...and it wasn't 4am either, was more like 1-2am...4am was pretty much when we had to get up. Remind me never to share a room/house with you and David again :O

your loss. :)

incase anyone didn't know cause I certainly didn't, *any* skidding/sliding/burnouts, even taking off from the lights with a bit of wheel spin equals instant 7 day impound + usual rapage. You only have to be suspected of being the one doing them to get booked for it, so if your in an area where someones being an idiot, leave fast.

One of my mates found this out the hard way.

dang no more innocent till proven guilty, if you drive an import your guilty

Abe why the need to slip the clutch? a good driver doesn't slip or ride the clutch, and with the cushioned ceramic you can still do a slip launch @ the drag strip

So no matter what i really choose, someone is going to say "I wouldn't have chosen that clutch kit" or "Why did you get that one" or some other comment. Why cant choosing a clutch be easier :) , too many contradicting comments/opinions.

With a clutch you get what you pay for. I went for a cheap Extreme, just recently i had to replace it. I should of spent the money the first time. Also best to get a clutch that is over built for your needs cos then you know it will last, don't just get one that you hope will last.

dang no more innocent till proven guilty, if you live in Sth Aust your guilty

Fixed

Abe why the need to slip the clutch? a good driver doesn't slip or ride the clutch, and with the cushioned ceramic you can still do a slip launch @ the drag strip

I don't know...maybe because i'm not a good driver, or it could be because that's what i am used to since driving the R33

yeah just a matter of practise there's no 'good' drivers we learn all the time, there's just better and getting better if that makes sense

after having my clutch in for over 3 years now im still getting use to it (then again i dont drive it much), stilll gottr slip/ride it, if u dont dont sumtimes u will stall and its an absolute bastrd bastard to drive in traffic with it, too aggressive with a lot of bite

Remind me never to share a room/house with you and David again :(

Just you wait till i am staying at your place for the Track Day :D

David might be staying here too BAHAHAHAHAHA
Fine, you'll both get pay back at the same time.

On both occasions you were awake and even sitting up the second time waiting for us. Did you stay at a Christian Brothers orphanage or do some jail time? Because no-one should be that alert when 'sleeping' whilst on holidays.

Fitted my fmic intercooler piping kit. What a pain in the arse that was. :D Couldn't be arsed trimming the radiator fan, so I've removed it altogether for the moment. Does anyone recommend an electric fan kit?

I'll need to fit one before the track day.

:(

what fmic kit did you get? you shouldnt be cutting up your fan (found out the hard way)

also, personal opinion, thermo's are shit if your also removing the clutch fan.

the clutch fan works alot better by its self then thermo's working be them selves. thermo's should only be run as a support to a clutch fan if your planning on dailying the car still.

again, this is my opinion. others may disagree.

thermo's ive used have only been davies craig brand and they did what i wanted them to do well (with clutch fan too)

thermo's should only be run as a support to a clutch fan if your planning on dailying the car still.

again, this is my opinion. others may disagree.

I'll be one that disagrees;

Every east/west engined car ever made runs thermo's and none of them have cooling problems, and this includes 500+hp EVO's and Eclipses.

Edited by D_Stirls
I'll be one that disagrees;

Every east/west engined car ever made runs thermo's and none of them have cooling problems, and this includes 500+hp EVO's and Eclipses.

yes, this is true but we are talking about north, south mounted engines and ive seen and when used myself they seemed to be shit compared to the clutch fan.

if a company MADE the car come out with thermos, you would think that they did the proper investigating to make this work while clutch fans work on the north, south engines.

this is just what ive seen and had happen to me.

yes, this is true but we are talking about north, south mounted engines and ive seen and when used myself they seemed to be shit compared to the clutch fan.

if a company MADE the car come out with thermos, you would think that they did the proper investigating to make this work while clutch fans work on the north, south engines.

this is just what ive seen and had happen to me.

I think you'll find this has more to do with it being cheaper and easier rather than better or worse.

I'm running a single 14" thermo and even on the track i have no problems with temps.

The problem with clutch fan is that they produce parasitic loss all the time even if the temps are fine. The advantage of the thermos is that they only produce a power loss when the cooling is actually needed which you will surprised to know is only around 30% of the time (more if you are in stationary traffic obviously). When the car is moving generally you don't need any more air flow than what you are getting by the car moving through the air.

Look at the North/South cars being produced now 95% or them are running thermos.

Edited by D_Stirls
mental note made, dont give james a stick when he's drunk. a few people nearly got smaked in the head by the kendo stick

LOL, sounds like James would make a good candidate for a Mod with his stick wielding talents .......**mental note** :(

So no matter what i really choose, someone is going to say "I wouldn't have chosen that clutch kit" or "Why did you get that one" or some other comment. Why cant choosing a clutch be easier :D , too many contradicting comments/opinions.

Abe, help us to help you buddy.....ie.

How much power are you anticipating?

How much track work will the car see?

Is it your daly and if so, how much rush hour driving will it see?

and most importantly, what is your driving style like, ie. boot into it from most traffic lights (which is how I drove when I was younger) or just the occasional squirt, etc?

All the above factors have a big say on clutch choice but having said that (and as Steve stated) you couldn't go wrong with that NPC setup from the little I know about you and your car.

Hope this is all helping bud, cause I was the same when I was trying to decide on turbos and zorsts before selling mine.

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • So stock ECU does not like anything above 10 psi?  That Nistune one is just for "try" if it will be any different, I know it need to be tune for that. I know but YOU may know about these problem but i/we dont. They few little Skylines here let alone people who know anything about tham so that is why iam asking here  
    • So now we have a radiator with no attachments whatsoever. It lifts up with a particularly tight spot between the drivers side air box mount and the lower radiator outlet, but if you've got this far you will sort that too. This is the lower mounts with the rad out so you can see where the rubber bushes go, it is a straight shot upwards Done! Assembly is the reverse of disassembly, with blood less likely to be shed.
    • Right, onto the second last trick. The Air Con condenser is mounted to the front of the radiator and stays in the car when the radiator is removed. There are 2x 10mm headed self tappers holding the top of the condenser to the radiator, remove those The bottom of the condenser is attached to the radiator with clips. You need to lift the condenser out of those clips and clear (up, then forward). f**ked if  could work out how to do that last bit with the front bumper on. I hope you can, and you share the trick.  Bumper removal probably deserves its own thread one day once I've recovered the will to live, but basically you need to remove the wheels, front inner guard liners (clips and 10mm headed bolts), the self tapper between the guard and the bumper at the rearmost point of the bumper (same as an R32 that bit), any remaining clips at the top/front of the grill, an absolute bastard design with a plate that holds the top of the bumper above the headlight each side (only 1 bolt which is tricky to get to, but the plate catches 2 places on the bumper and must be removed....carefully!) and push clips between the bumper and guard under the headlight. If you've done all that you will be faced with wiring for the fog lights on both sides and in ADM Q50 RS at least, 4 nasty tight plugs on the driver's side for the ADAS stuff. So, the clips at the bottom look like this on drivers side (looking from the front) And on the passenger side (also from the front), you can see this one is already out Clearance on both of these are super tight; the condenser needs to move up but the upper rad support mount prevents that, and the radiator can't move down far because it is (rubber) mounted. Once you achieve the impossible and drop the condenser off those mounts so it does not stop the rad moving, you are good to go
    • OK, next the shroud needs to come off and there are a couple of tricks. Firstly, there is a loom from near the passenger side headlight to the fans, coolant temp sensor etc and there is no plug to undo.  In my case I was OK to leave the shroud on top of the engine so I just undid the passenger side fan plug and about 10 of the clips which gave enough free wire to put it aside. The fan plugs were super tight, the trick I used was a small falt screwdriver to push down on the release tab, then a larger flat screwdriver to lever the plug out of the fan unit....be careful with how much force you apply! If you need to remove the shroud altogether for some reason you will have to deal with all the plugs (tight) and clips (brittle)....good luck. I removed all of the clips and replaced them with cable ties that I will just cut next time. Also, in the Red Sport / 400R at least, the intake heat exchanger reservoir hose is bolted to the shroud in 2 places with 10mm headed bolts; so remove them (the hose stays in the car; no need to undo it at the t fittings down at the radiator lower mount. Once you've dealt with the HX hose and the wiring loom, there are 3x 10mm headed self tappers holding the top of the shroud to the radiator; remove those.   The shroud then lifts out of the bottom mounts where it sits on the radiator, up and onto the engine out of the way. Simples
    • Ok, disregard my “rate them” comment, sorry for my unrealistic input
×
×
  • Create New...