Jump to content
SAU Community

Recommended Posts

Suki or whatever her name is from 2F2F is UGLY++

Havent you heard the saying "any holes a goal." :laugh:

Black. :huh:

Ill look out for your car...

I THINK I REMEBER YOU NOW! I was in the car with my sister maybe about a month ago..

you were driving next to me on bunnergong rd and down wentworth.. ave and then some other noodle in a skyline zoom past and you sped up with him.. maybe it was you.. theres not alot of of black 33's round the area..

I drive a black 32

Havent you heard the saying "any holes a goal." :huh:

I THINK I REMEBER YOU NOW! I was in the car with my sister maybe about a month ago..

you were driving next to me on bunnergong rd and down wentworth.. ave and then some other noodle in a skyline zoom past and you sped up with him.. maybe it was you.. theres not alot of of black 33's round the area..

I drive a black 32

dunno cant say I remember what happened last nite let alone last month. :laugh:

I forgot the password to my work email :P and only changed it last nite

OK should stop wh0ring in the spotted thread.. seeya!

omg :P with a name like corinne, i thought you were a girl?! :P

omg :) with a name like corinne, i thought you were a girl?! :O

HAHA :laugh:

If that was true

QUOTE(D_I_F @ 2 Mar 2006, 12:58 PM)

yea it is.. shes hot isnt she..

Very nice arse..

You know what the above statment would mean! :huh:

Double post moanie?

Is that a gremlin again or do you need to complain to prank!

i need to complain!! every thread i post (bar the whore thread) it gives me an error but posts.. so i refresh and it posts again!!!

Yes, sure its not a pebcak or an ID-10-T error?

JK :laugh:

Saw it happen in the NSW dyno day topic

sh ms!!!

spotted the below on tuesday evening:

spotted a white 33 on the city westlink about 7pm.. got a wave:D

also spotted another white 33 going the other way on the rd on the other side of parra rd from the city westlink! lol!!! he was heading towards the city.. i think i got a belated beep? :P

(posted it in the wrong spotted thread! LOL!)

Spot a Yellow R34 GTT every morning on the way to work on Lane Cove road heading towards homebush

Spotted a grey 32 GTR on pacific hwy chatswood heading northbound. Threw a wave...got one back

Spoted a silver 350Z taking my car space this morning at Chatswood.

i need to complain!! every thread i post (bar the whore thread) it gives me an error but posts.. so i refresh and it posts again!!!

oh! and corinne! check out the chick drag thread in the events section!! DO IT!!!!

i havent been able to post for ages now..

i dont think i would go in one of those.. :S

my cars mostly stock.. i dont have a cams licence.. i would have to do some work on my car before anything like that happened.. i dont even know what speed im going at my speedo is out.. :S

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
×
×
  • Create New...