Jump to content
SAU Community

Recommended Posts

spotted Sambo (kennedy) on Delhi Rd this morning, I beeped, waved, flashed my lights, went slow as hell and you still didn't have any idea I was there!!! lol

space cadet!

Were you driving a Skyline?? Last time I checked this was the Skyline spotted thread.

Spotted "R32" gunmetal 32 with hektic big ugly chromies on the front stockies on rear, kept coming up next to me and being sick with his bov and giving me the "fully sick stare" from the back window coz he leans back so far, next time stop trying to be so sick by blocking me out of the lane I need to use to turn you tool.

I spotted three asian guys in various skylines yesterday, waved to all three and got the kangaroo in headlights look back from them!? :) HUH-000 strikes again..

Rude bastards!

Spotted Yellow R34 today, plate MYLADI coming out of Yagoona KFC.

anyone noe who it is? sounded mean

I saw that one as well today when i was walking along woodville road waiting for my alarm and new speakers to get fitted.

Spotted HAYSEY!

atleast I think it was him.. looked like HAYSEY plates on a white r32

I was walking across the rod on Pacific Hwy at the lights where you were turning right onto pac hwy, was staring at ya to see if I recognized you but didnt notice the plates untill after your boosted by me

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • @Murray_Calavera  If I were an expert I wouldn't be in here looking for assistance.  I am extremely computer literate, have above average understanding on how things should be working and how they should tie together.  If I need to go to a professional tuner so be it, but I'd much rather learn and do things myself even if it means looking for some guidance along the way and blowing up a few engines. @GTSBoy  I was hoping it would be as simple as a large vacuum leak somewhere but I'm unable to find anything, all lines seem to be well capped or going where they need to be, and when removed there is vacuum felt on the tube.  It would be odd for the Haltech built in MAP to be faulty, the GTT tune I imported had it enabled from the start, I incorrectly assumed it was reading a signal from the stock MAP, but that doesn't exist.  After running a vacuum hose to the ECU the signal doesn't change more than 0.2 in either direction.   I'll probably upload a video of my settings tomorrow, as it stands I'm able to daily drive, but getting stuttering when giving it gas from idle, so pulling away from lights is a slow process of revving it up and feathering the clutch until its moving, then it will accelerate fine.  It sounds like I need to get to the bottom of the manifold pressure issue, but the ignition timing section is most intimidating to me and will probably let a pro do that part.  Tomorrow I'll try a different vacuum line to T off of, with any luck I selected one that was already bypassed during the DBW swap. @feartherb26  I do have +T in the works but wanted to wait until Spring to start with that swap since this is my good winter AWD vehicle.  When removing the butterfly, did it leave a bunch of holes in the manifold that you needed to plug?  I thought about removing it but assumed it would be a mess.   I notice no difference when capping the vacuum line to it or letting it do its thing.  This whole thing has convinced me to just get a forward facing manifold when the time comes though.
    • Update: tested my spark plugs that are supposed to be 5ohms with a 10% deviation and one gave me a 0 ohms reading and the rest were 3.9ohm<, so one bad and the others on their way out.
    • 9" wheels are a little too wide for a RWD 32. They can fit. People have put R33 GTR wheels on 32s for years and years. But they are a very tight squeeze. This has been known for about 30 years. As I said - there is no difference between a 17 and an 18 in terms of what will fit. The rolling diameter needs to stay about the same as stock - not very much larger. If you increase that, you will start to have problems. If you increae rolling diamater at the same time as yo increase width, you will have problems earlier. as 9" wheels are pushing the boundaries already, you would need to be careful with tyre choice. I would put 8.5s on the front of mine, but would expect problems with 9s.
    • post up screen shots of your injector tables
    • Diagnostic flow for a code 21 says check signal at the ECU pins, on a voltmeter of some kind it should read 0.1V at idle, 0.12V cranking, 0.15-0.25V at 2000 rpm. Check each coil such that +1, -3 is infinite or very high resistance, -3, +2 should do the same. (-1, +3), (+3, -2), (+1, -2), and (-1, +2) should all be somewhere between 0 ohms and high resistance. If you trace the path from the coil pin all the way back to the ECU in the diagram the resistance you measure at the coil vs connected to the harness should be pretty much the same. 
×
×
  • Create New...